1、传 琶 胀 筠蹩睛 链 期稍螗附录 1 樱 放袱俱坩蕹 桩 呶 贞 涪英文原文 剑萦嘤 湖岸蹙 讼哕 鄙 鹤Lecture 2.6: Weldability of Structural Steels 颤 圃裳眉故灰奄貊乱蔑The lecture briefly discusses the basics of the welding process and then examines the factors governing the weldability of structural steels.螗斧 窦 蚴 膦瘿 士双氵沁SUMMARY 少 缀 褐嫌 毕仓 鏖拖耿甓The fundamen
2、tal aspects of the welding process are discussed. The lecture then focuses on the metallurgical parameters affecting the weldability of structural steels. A steel is considered to exhibit good weldability if joints in the steel possess adequate strength and toughness in service.囊吹了陋卜 朵岿 猊 谯 傈Solidif
3、ication cracking, heat affected zone - liquation cracking, hydrogen-induced cracking, lamellar tearing, and re-heat cracking are described. These effects are detrimental to the performance of welded joints. Measures required to avoid them are examined.萍 锟嗨鳜 田咬 锑偷 物斡1. INTRODUCTION 栏 猗炱 蛲 袢疹劈勇朔壅1.1 A
4、 Brief Description of the Welding Process 囚椹乃箔耖 卢 股鼠筇朔Welding is a joining process in which joint production can be achieved with the use of high temperatures, high pressures or both. In this lecture, only the use of high temperatures to produce a joint is discussed since this is, by far, the most c
5、ommon method of welding structural steels. It is essentially a process in which an intense heat source is applied to the surfaces to be joined to achieve local melting. It is common for further “filler metal“ to be added to the molten weld pool to bridge the gap between the surfaces and to produce t
6、he required weld shape and dimensions on cooling. The most common welding processes for structural steelwork use an electric arc maintained between the filler metal rod and the workpiece to provide the intense heat source.耀 丢砻 蛄 纯轶 醵槐 蚁 影If unprotected, the molten metal in the weld pool can readily
7、absorb oxygen and nitrogen from the atmosphere. This absorption would lead to porosity and brittleness in the solidified weld metal. The techniques used to avoid gas absorption in the weld pool vary according to the welding process. The main welding processes used to join structural steels are consi
8、dered in more detail below.骟舰纷 横囝 呋 胳毫底娄1.2 The Main Welding Processes 秦醴湍 锞绲呋 婿 药 本 钦a. Manual Metal Arc welding (MMA)耶 创 崖 疬 耔 绲 扮 摇撵 峭In this process, the welder uses a metal stick electrode with a fusible mineral coating, in a holder connected to an electrical supply. An arc is struck between th
9、e electrode and the weld area which completes the return circuit to the electricity supply. The arc melts both the electrode and the surface region of the workpiece. Electromagnetic forces created in the arc help to throw drops of the molten electrode onto the molten area of the workpiece where the
10、two metals fuse to form the weld pool.颂 芸抒 缆 厥己竽蒯侯蜉The electrode coating of flux contributes to the content of the weld pool by direct addition of metal and by metallurgical reactions which refine the molten metal. The flux also provides a local gaseous atmosphere which prevents absorption of atmosp
11、heric gases by the weld metal.侄仔 钳蚀读 僧秸喟豹 赏There are many types of electrodes. The main differences between them are in the flux coating. The three main classes of electrode are shown below:卦 鲫衮 萆芝篆 纳 桑山 妩1. Rutile: General purpose electrodes for applications which do not require strict control of m
12、echanical properties. These electrodes contain a high proportion of titanium oxide in the flux coating.崞 蟪馗宥 巯辔 峨婚淘号2. Basic: These electrodes produce welds with better strength and notch toughness than rutile. The electrodes have a coating which contains calcium carbonate and other carbonates and f
13、luorspar.畜柯牒 坝 掭盛 辙 睥漉 蚺3. Cellulosic: The arc produced by this type of electrode is very penetrating. These electrodes have a high proportion of combustible organic materials in their coating.贰 盹 钋 色晒漭泉哆筏翠b. Submerged Arc Welding (SAW)实 旌渭 橹 胄 闲 其瘦 挝 媸This process uses a bare wire electrode and a f
14、lux added separately as granules or powder over the arc and weld pool. The flux protects the molten metal by forming a layer of slag and it also stabilises the arc.段 钢岽 菁 孓 臾妥 细滨斩The process is used mainly in a mechanical system feeding a continuous length of wire from a coil whilst the welding lead
15、 is moved along the joint. A SAW machine may feed several wires, one behind the other, so that a multi-run weld can be made. Submerged arc welding produces more consistent joints than manual welding, but it is not suitable for areas of difficult access.珐 徵 冻 娟 闰 黔央怵沁骰c. Gas shielded welding 潴 鹚 栲 诅嵴
16、泞泺 俊徉 讴In this process, a bare wire electrode is used and a shielding gas is fed around the arc and weld pool. This gas prevents contamination of the electrode and weld pool by air. There are three main variations of this process as shown below:愤 沔汊玖 铡 楝 钔 先 现处1. MIG (metal-inert gas) welding - Argo
17、n or helium gas is used for shielding. This process is generally used for non-ferrous metals.话鸱 跆所盒圳秤 龅 携 痖2. MAG (metal-active gas) welding - Carbon dioxide (usually mixed with argon) is used for shielding. This process is generally used for carbon and carbon-manganese steels.蘸炉存技蚝衙 钡 良埃 锸3. TIG (t
18、ungsten-inert gas) - Argon or helium gas is used for shielding and the arc struck between the workpiece and a non-consumable tungsten electrode. This process is generally used for thin sheet work and precision welding.蛩 霁炜记 蘖羚 骡 茭看泠1.3 Welded Joint Design and Preparation 颔 徒妹 铯 藿拭八 飓莴 嬉There are two
19、 basic types of welded joints known as butt and fillet welds 1. Schematic views of these two weld types are shown in Figure 1. The actual shape of a weld is determined by the preparation of the area to be joined. The type of weld preparation depends on the welding process and the fabrication procedu
20、re. Examples of different weld preparations are shown in Figure 2. The weld joint has to be located and shaped in such a way that it is easily accessible in terms of both the welding process and welding position. The detailed weld shape is designed to distribute the available heat adequately and to
21、assist the control of weld metal penetration and thus to produce a sound joint. Operator induced defects such as lack of penetration and lack of fusion can be difficult to avoid if the joint preparation and design prevent good access for welding.鬼 逦骄 葑圃 记 杓 轳 把罾氆 返呼傺渗 趱酿 凰皮 泵绾 遏妥膀浅 茏 洙蒗 镰谁1.4 The Ef
22、fect of the Welding Thermal Cycle on the Microstructure 鸵 能弈柳恙央宜的甫 鲨The intense heat involved in the welding process influences the microstructure of both the weld metal and the parent metal close to the fusion boundary (the boundary between solid and liquid metal). As such, the welding cycle influe
23、nces the mechanical properties of the joint.璞糖 仑怄 句赦 纱骋凇 揉The molten weld pool is rapidly cooled since the metals being joined act as an efficient heat sink. This cooling results in the weld metal having a chill cast microstructure. In the welding of structural steels, the weld filler metal does not
24、 usually have the same composition as the parent metal. If the compositions were the same, the rapid cooling could result in hard and brittle phases, e.g. martensite, in the weld metal microstructure. This problem is avoided by using weld filler metals with a lower carbon content than the parent ste
25、el.畹篾 撖郏 擦瘘蕺 赵 跋 姘The parent metal close to the molten weld pool is heated rapidly to a temperature which depends on the distance from the fusion boundary. Close to the fusion boundary, peak temperatures near the melting point are reached, whilst material only a few millimetres away may only reach a
26、 few hundred degrees Celsius. The parent material close to the fusion boundary is heated into the austenite phase field. On cooling, this region transforms to a microstructure which is different from the rest of the parent material. In this region the cooling rate is usually rapid, and hence there i
27、s a tendency towards the formation of low temperature transformation structures, such as bainite and martensite, which are harder and more brittle than the bulk of the parent metal. This region is known as the heat affected zone (HAZ).慝 碜 溧 脲 佩 贷暨 卓 还塄The microstructure of the HAZ is influenced by t
28、hree factors:蛟 坟搁 湮若 审 晤 谨 憧屮The chemical composition of the parent metal. 诨檩 呃 砩标萘 台 鹈剧 康The heat input rate during welding. 绞 旦獍呕猿茸 骏 洚 柽蒈The cooling rate in the HAZ after welding.恹 葡蘸拿泠然佛索光焦The chemical composition of the parent metal is important since it determines the hardenability of the HAZ.
29、 The heat input rate is significant since it directly affects the grain size in the HAZ. The longer the time spent above the grain coarsening temperature of the parent metal during welding, the coarser the structure in the HAZ. Generally, a high heat input rate leads to a longer thermal cycle and th
30、us a coarser HAZ microstructure. It should be noted that the heat input rate also affects the cooling rate in the HAZ. As a general rule, the higher the heat input rate the lower the cooling rate. The value of heat input rate is a function of the welding process parameters: arc voltage, arc current
31、and welding speed. In addition to heat input rate, the cooling rate in the HAZ is influenced by two other factors. First, the joint design and thickness are important since they determine the rate of heat flow away from the weld during cooling. Secondly, the temperature of the parts being joined, i.
32、e. any pre-heat, is significant since it determines the temperature gradient which exists between the weld and parent metal.类单飞惯 坡 墒 焙瘳嫡痘1.5 Residual Welding Stresses and Distortion 骁 渊 鲛检郦卟兹宪 孺腿The intense heat associated with welding causes the region of the weld to expand. On cooling contraction
33、occurs. This expansion and subsequent contraction is resisted by the surrounding cold material leading to a residual stress field being set up in the vicinity of the weld. Within the weld metal the residual stress tends to be predominantly tensile in nature. This tensile residual stress is balanced
34、by a compressive stress induced in the parent metal 2. A schematic view of the residual stress field obtained for longitudinal weld shrinkage is shown in Figure 3. The tensile residual stresses are up to yield point in magnitude in the weld metal and HAZ. It is important to note that the residual st
35、resses arise because the material undergoes local plastic strain. This strain may result in cracking of the weld metal and HAZ during welding, distortion of the parts to be joined or encouragement of brittle failure during service.涫酏 粪 睚迮 蓦临费 胭哉帆陵 颧 仟裳扛耒琥嘎戴Transverse and longitudinal contractions re
36、sulting from welding can lead to distortion if the hot weld metal is not symmetrical about the neutral axis of a fabrication 2. A typical angular rotation in a single V butt weld is shown in Figure 4a. The rotation occurs because the major part of the weld is on one side of the neutral axis of the p
37、late, thus inducing greater contraction stresses on that side. This leads to a distortion known as cusping in a plate fabrication, as shown in Figure 4b. Weld distortion can be controlled by pre-setting or pre-bending a joint assembly to compensate for the distortion or by restraining the weld to re
38、sist distortion. Examples of both these methods are shown in Figure 5. Distortion problems are most easily avoided by using the correct weld preparation. The use of non-symmetrical double sided welds such as those shown in Figure 2e and 2i accommodates distortion. The distortion from the small side
39、of the weld (produced first) is removed when the larger weld is put on the other side. This technique is known as balanced welding.栉 躺捌珈旧 讽 膝催瑞狙榜 萨赕 嗷瑰圬 悬 柞彬刃蚱 兴 式踅 牦 兼 栌郑 股洫It is not possible to predict accurately the distortion in a geometrically complicated fabrication, but one basic rule should
40、be followed. This rule is that welding should preferably be started at the centre of a fabrication and all succeeding welds be made from the centre out, thus encouraging contractions to occur in the free condition.业 昔慈 垦 副目甥 银 丁 髋If distortion is not controlled, there are two methods of correcting i
41、t; force and heat. The distortion of light sections can be eliminated simply by using force, e.g. the use of hydraulic jacks and presses. In the case of heavier sections, local heating and cooling is required to induce thermal stresses counteracting those already present.邦上狁唱耜 辔 卦 濒莺赢1.6 Residual St
42、ress Relief 贡铕 艮艏展禁匠 旯鳏 芫The most common and efficient way of relieving residual stresses is by heating. Raising the temperature results in a lower yield stress and allows creep to occur. Creep relieves the residual stresses through plastic deformation. Steel welded components are usually heated to
43、a low red heat (600C) during stress relieving treatments. The heating and cooling rates during this thermal stress relief must be carefully controlled otherwise further residual stress patterns may be set up in the welded component. There is a size limit to the structures which can be thermally stre
44、ss relieved both because of the size of the ovens required and the possibility of a structure distorting under its own weight. It is possible, however, to heat treat individual joints in a large structure by placing small ovens around the joints or by using electric heating elements.洄巽施 孬 立 尝 裨汲 涞 矩
45、Other methods of stress relief rely on thermal expansion providing mechanical forces capable of counteracting the original residual stresses. This technique can be applied in-situ but a precise knowledge of the location of the compressive residual stresses is vital, otherwise the level of residual s
46、tress may be increased rather than decreased. Purely mechanical stress relief can also be applied provided sufficient is available to accommodate the necessary plastic deformation.侏早伙 呸 批衄拼婀 识 祠2. THE WELDABILITY OF STRUCTURAL STEELS 晦橘恢 娴 砂朦燧被莞巨2.1 Introduction 汩 坡蛋胱舴 桨 角筇 砗鸣If weld preparation is
47、good and operator induced defects (e.g. lack of penetration or fusion) are avoided, all the common structural steels can be successfully welded. However, a number of these steels may require special treatments to achieve a satisfactory joint. These treatments are not convenient in all cases. The dif
48、ficulty in producing satisfactory welded joints in some steels arises from the extremes of heating, cooling and straining associated with the welding process combined with microstructural changes and environmental interactions that occur during welding. It is not possible for some structural steels
49、to tolerate these effects without joint cracking occurring. The various types of cracking which can occur and the remedial measures which can be taken are discussed below.谁 匝 卤僬 接呆睡黏掏旒2.2 Weld Metal Solidification Cracking 斋 枘槲 飕 形蛙瞽擦傣坪Solidification of the molten weld pool occurs by the growth of crystals away from the fusion boundary and towards the centre of the weld pool, until eventually there is no remaining liquid. In the process of crystal growth, solute and impurity elements are pushed ahead of the growing interface. This process is not significant until the final stages of sol
