1、 微 电 子 有 限 公 司 类比式触摸屏规格承认书Analog Touch panel Specification客户名称 / CUSTOMER NAME： 品名/Product Name ： 触摸屏 机种名/Product Number： 图纸/样品版本/ Drawing view Area所有外观不良只要是在可视区以外对产品功能不造成影响均不考虑在内Any defects in invisible shall be ignored unless they affect electrical performance.检查条件Inspection Conditions视力 1.0 及以上的健
2、康成人 (带眼镜亦可 ),物体与检测者眼睛距离 20 到 30 厘米处检测。The inspection should be conducted by a healthy inspectorhaving a vision of 1.0 or above (eyeglasses acceptable), and at the distance 20 to 30 cm between the object and the inspectors eye使用机器：荧光灯 30W；照明条件：明室下 1000LU 以下Inspection device: florescent light 30 W; Il
3、lumination condition: less than 1000LU in a bright room检查环境Inspection Environment Lmp Glas30(1)cmFiTouhPneEyAprox.60LaTuh PnelEys4.2 Inspection standards 检验基准书产品可视范围外若没有因裂缝，刮伤，异物等外观不良影响产品电气特性的，也可接受。For areas outside the visible range, it is acceptable if there is no crack, scratch, or foreign object
4、s thatcan greatly affect the electric performance of this product.该范围用于本基准未描述到的裂缝，刮伤或者异物等外观不良。Limit samples shall be used for cracks, scratch, or foreign objects which are not described in thisstandard.4.3 线状缺陷（W=宽度、L=长度） Line defect (W=Width, L=Length)宽度 Width(mm)长度 Length(mm) 基准 Standard 注意 Remark
5、0.03 不计 Ignored0.03W0.05 L 3.0两个以内线状缺陷(间距离不小于 10mm)Up to two defects, with the failure under distance 10mm2 个以内缺陷Up to total two defectsW0.05 不接受 None点 状 异 物4.4 点状异物 （D = 长径）Pin defect (D = longest diameter) 平均直径Average diameter(mm) 基准 Standard 注意 Remark0.15 不计 Ignored0.15D0.2 最多 3 个 MAX 3 pieces 2
6、个以上缺陷距离大于 5mmUp to two total defectsD0.2 不接受 None4.5 Film 表面没有折伤 Film surface no fold shall exist.4.6 牛顿环 / 干涉线 Newton ring / Interference fringes根据 4.1 外观检查方法确认 To be confirmed according to No. 4.1 inspections of appearance外观牛顿环限定个数 Appearance Inspection Limit simple:项目Item基准Standard备注Notes常规Regula
7、r在整个触摸屏检查区域内超过 1/4 范围; 不接受The area covered by Newton Ring is more than 1/4 of the whole TP surface; Reject在整个触摸屏检查区域内小于 1/4 范围，并且在有照明环境下不影响透光率及失真；接受The area covered by Newton Ring is less than 1/4 of the whole TP surface, and it does not affect transmittance and clarity of TP under the lighting ambi
8、ent. 例外Irregular在整个触摸屏检查区域内在照明环境下超过 1/4 范围；不接受The area covered by Newton Ring is more than 1/4 of the whole TP surface under the lighting ambient ; Reject在照明环境下牛顿环有影响清晰度和透光率；不接受（不计牛顿环尺寸）If the Newton Ring affect the transmittance and clarity under lighting ambient, it is NG (Regardless of the Newton
9、 Ring size)在整个触摸屏检查区域内小于 1/4 范围, 并且在有照明环境下不影响透光率及失真；接受The area covered by Newton Ring is less than 1/4 of the whole TP surface, and it doesnt affect transmittance and clarity of TP under the lighting ambient;Accept4.7 凸出（包括波状弯曲）Bulge (undulation included)膜鼓起在 0.40mm 高度范围内判定为合格品。The ITO film plumped
10、below 0.40mm, its ok. 凸 起 （ 包 括 波 状 弯 曲 ）Product0.4m orblw以 下4.8 Film 表面：鱼眼 Film surface: Fish eye：按点状计算4.9 玻璃毛屑和裂缝（ t =玻璃厚度）Chip and Crack of glass (t=glass thickness)项目 Item 尺寸 Size (mm) 长度 Length (mm) 接受个数 Acceptable Qty角Corner 角 ComerX 2.0 O 片：若有任何一个毛屑或裂缝超过所给的 X，Y，Z 值，则不接受。0 pcs: Judge unaccepta
11、ble if there is any one chip or crack exceeding the permissive value of X, Y, or Z.Y 2.0Z 1T角以外的地方Other than corner角 以 外 的 地 方 Other ancoX X 4.0 O 片：若有任何一个毛屑或裂缝超过所给的 X，Y，Z 值，则不接受。0 pcs: Judge unacceptable if there is any one chip or crack exceeding the permissive value of X, Y, or Z.每边 2 个或更少；它们要小于所
12、给的值。Two or less for each side: Those less than these values.Y 2Z 1T进行性的裂缝或者毛屑Progressive Crack or chip 进 行 性 的 裂 缝 或 者 毛 屑 Progesiv CackrhpO 片：若有任何进行性的裂缝或毛屑，不接受。0 pcs: Judge unacceptable if there is any progressive crack or chip.5.信赖性实验内容 Reliability Test5.1 环境实验 Environmental Test项目Item内容Contents注意
13、Notes高温保存High temperature preservation(1) 温度 70,放置 120 小时； (2)室温放置 24 小时以上；(3) 然后测量以下项目：不可有结露(1) Store at 70 for 120 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items: no dew condensation端子间阻抗：参照电气特性栏 Resistance between terminals: see electri
14、cal property item; 直线性：参照电气特性栏 Linearity: see electrical property item;绝缘阻抗：参照电气特性栏 Insulation resistance: see electrical property item.低温保存Low Temperaturepreservation(1)温度 -20,放置 120 小时；(2)室温放置 24 小时以上；(3)然后测量以下项目：不可有结露(1) Store at-20 for 120 hours; (2) Keep at a room temperature for more than 24 h
15、ours; and (3) Measure (satisfy) the following items: no dew condensation端子间阻抗：参照电气特性栏 Resistance between terminals: see electrical property item; 直线性：参照电气特性栏 Linearity: see electrical property item;绝缘阻抗：参照电气特性栏 Insulation resistance: see electrical property item.高温高湿保存High Temperature(2) Keep at a r
16、oom temperature for more than 24 hours; and (3) Measure (satisfy) the following items: no dew condensation端子间阻抗：参照电气特性栏 Resistance between terminals: see electrical property item; 直线性：参照电气特性栏 Linearity: see electrical property item;绝缘阻抗：参照电气特性栏 Insulation resistance: see electrical property item.冷热冲
17、击测试Heat shook test(1)-20 （60 分）60（60 分）共 10 次循环；(2)室温放置 24 小时以上；(3)然后测量以下项目：不可有结露(1) -20(60min) 60(60min) total 10 cycles, (2) Keep at the room temperature for more than 24 hours; and (3) Measure (satisfy) the following items: no dew condensation 端子间阻抗：参照电气特性栏 Resistance between terminals: see elect
18、rical property item; 直线性：参照电气特性栏 Linearity: see electrical property item;绝缘阻抗：参照电气特性栏 Insulation resistance: see electrical property item.注：对上述表例外观标准无误判定良品允许与否时，依实物情形，双方再进行研讨判定，当客户特殊要求，需按客户要求判定！Note: when determine the appearance standard that in the above table are right or not? According to the re
19、al products, the two sides need to further study on these. if the customers have special demand ,so need to follow their require数万个文件，一网打尽强力推荐!大量电子行业电子企业 /工厂方面(涵盖 LCD/LCM/TFT/TP/3D/POL 实战技术）资料。包括多家著名电子企业的内部管理制度,表格,流程,成本,绩效考核,供应链,质量管理,电子行业技术资料等等. 数万个文件, 一网打尽!是本人精心制作的一套有助于电子企业及从事电子行业的个人提升能力的管理光盘! 有助您系统性及完整性的把电子行业的管理工作做得更好.为您或企业节省大量的管理成本! 售价：100 元另加 50 元可以参加百万资料下载计划，一次付出，终生使用，你只需首付 50 元，对资料文库里的资料你只需付车费可免费上门拷贝(深圳内) ，省外可刻碟 5 元/ 张邮费自理或网上传输以下为部分截屏目录，有 LCM/LCD/TFT/SMT 行业全套生产/品质/ 工艺/原材料/总结报告资料，另有电子设计类资料，有需要的朋友，可以联系我的 QQ785302948 师少恒 QQ：785302948
