1、5.5 营造做法5.5 build 5.5.1 上人平屋面5.5.1 on roofing range 1. 10 厚地砖铺平拍实，1:1 水泥砂浆填缝，缝宽 5-8。1. 10 thick floor tile paving solid, 1:1 caulking, cement mortar seam width 5-8. 2. 15 厚 1:4 干硬性水泥砂浆，面上撒素水泥。2. 15 thick 1:4 harsh cement mortar, and on the surface of cement. 3. 40 厚 C20 细石混凝土垫层内配4150x1503. 40 thick
2、C20 fine stone concrete cushion inside 4 150 x150 4. 干铺无纺聚酯纤维布一层。4. Dry spread a layer of non-woven polyester fiber cloth. 5. 120 厚挤塑板 XPS（B1 级）保温层5. 120 thick extruded board XPS insulation layer (B1 level) 6. 3+3 双层 SBS 改性沥青卷材防水层6. 3 + 3 double SBS modified asphalt coiled material waterproof layer
3、7. 20 厚 1:3 水泥砂浆找平层，掺入聚丙烯或锦纶-6 纤维 0.750.90kg/m37. 20 thick 1:3 cement mortar screed-coat, mixed with polypropylene or nylon 6 fiber 0.75 0.90 kg/m3 8. 20 厚（最薄处）1:8 水泥珍珠岩找 2%坡，坡向雨水口。8. 20 (the thinnest point) thick 1:8 cement perlite find 2% slope, slope to the rain. 9. 清除原有面层至预制筋混凝土楼板。9. Remove the
4、original surface to the precast reinforced concrete floor. 5.5.2 不上人平屋面5.5.2 range on the roof 1. 绿豆砂保护层。1. The green bean sand layer. 2. 3+3 双层 SBS 改性沥青卷材防水层2. 3 + 3 double SBS modified asphalt coiled material waterproof layer 3. 20 厚 1:3 水泥砂浆找平层，掺入聚丙烯或锦纶-6 纤维 0.750.90kg/m33. 20 thick 1:3 cement mo
5、rtar screed-coat, mixed with polypropylene or nylon 6 fiber 0.75 0.90 kg/m3 4. 20 厚（最薄处）1:8 水泥珍珠岩找 2%坡，坡向雨水口。4. 20 (the thinnest point) thick 1:8 cement perlite find 2% slope, slope to the rain. 5. 120 厚挤塑板 XPS（B1 级）保温层5. 120 thick extruded board XPS insulation layer (B1 level) 6. 清除原有面层至预制筋混凝土楼板。6.
6、 Remove the original surface to the precast reinforced concrete floor. 5.5.3 有保温喷刷涂料外墙面5.5.3 metope of thermal spray coating 1. 双组份聚氨脂罩面涂料一遍1. Its a two-component polyurethane finish paint again 2. 丙烯酸弹性高级中层主涂料一遍2. The acrylic elastic senior middle main coating again 3. 封底涂料一遍3. The back cover coati
7、ng again 4. 12 厚 1:0.2:2 水泥石灰膏砂浆找平4. 12 thick 1-0. 2:2 cement lime putty mortar leveling 5. 刷素水泥浆一道（内参水重 5%的建筑胶）5. Brush element slurry along (internal water 5% heavier construction glue) 6. 5 厚 1:0.5:3 水泥石灰膏砂浆打底扫毛或划出纹道6. 5 thick 1-0. 5:3 cement lime putty mortar render brooming or draw lines 7. 70
8、厚单层钢丝网架立纤维岩棉板（A 级） ，保温板内斜插腹丝及板面附加锚固筋7. 70 thick monolayer steel wire rack made fiber rock wool board (grade A), insulation board in the oblique abdominal silk and board face additional anchoring reinforcement 8. 建筑胶水泥砂浆墙体找平8. Plastic cement mortar wall leveling construction 9. 钢筋混凝土及轻集料混凝土砌块墙或清除原面层至
9、结构层。9. The reinforced concrete and lightweight aggregate concrete block wall or removal of the original surface to the layer structure. 5.5.4 浆料保温层喷刷涂料外墙面5.5.4 slurry spray insulation coating and blunt 1. 双组份聚氨脂罩面涂料一遍1. Its a two-component polyurethane finish paint again 2. 丙烯酸弹性高级中层主涂料一遍2. The acry
10、lic elastic senior middle main coating again 3. 封底涂料一遍3. The back cover coating again 4. 30 厚 FTC 相变蓄能保温材料，参照厂家施工工艺。4. 30 thick FTC phase change energy storage heat preservation material, consult factory construction technology. 5.5.5 大理石防滑地面5.5.5 antiskid ground marble 1. 20 厚大理石铺实拍平，水泥砂浆擦缝1. 20 ma
11、rble and thick film, cement mortar seam 2. 30 厚 1:4 干硬性水泥砂浆2. 30 thick 1:4 harsh cement mortar 3. 素水泥浆结合层一道3. A plain cement combined with layer 4. 拆除原面层至原地面垫层4. Remove the original surface to the original floor mat layer 5.5.6 陶瓷地砖防滑防水地面5.5.6 waterproof ceramic floor tile prevent slippery ground 1.
12、 10 厚地砖铺实拍平，水泥浆擦缝1. 10 floor tile shop make flat, thick slurry wipe a seam 2. 20 厚 1:4 干硬性水泥砂浆。2. 20 thick 1:4 harsh cement mortar. 3. 2 厚聚氨酯涂膜防水层，涂三边，四周卷起 200 高3. 2 thick polyurethane coating waterproof layer, trilateral, rolled up around 200 high 4. 刷基层处理剂。4. Brush treatment at the local level. 5.
13、 20 厚 1:2 水泥砂浆找平层。5. 20 1:2 cement mortar screed-coat thick. 6. 50 厚（最高处）C20 细石混凝土从门口处向地漏找坡0.5%，最薄处不小于 30厚，随打随抹。6. 50 (top) and thick C20 concrete with fine stones from the door to find slope 0.5% floor drain, the thinnest place not less than 30 thick, with playing with. 7. 素水泥浆结合层一道7. A plain cemen
14、t combined with layer 8. 拆除原面层至原地面垫层8. Remove the original surface to the original floor mat layer 5.5.7 塑料地板地面5.5.7 plastic floor on the ground 1. 3 厚塑料地板1. 3 thick plastic floor 2. 配套胶黏剂粘结。2. Adhesive form a complete set of adhesives. 3. 建筑胶水泥腻子批嵌平整3. Plastic cement construction putty of embedded
15、is flat and level 4. 20 厚 1:3 水泥砂浆找平，压实抹光。4. 20 thick 1:3 cement mortar leveling, compaction finishing. 5. 素水泥砂浆结合层一遍。5. Plain cement mortar layer again. 6. 拆除原面层至原地面垫层6. Remove the original surface to the original floor mat layer 5.5.8 陶瓷地砖防滑地面5.5.8 ceramic floor tile prevent slippery ground 1. 10
16、厚地砖铺实拍平，水泥浆擦缝1. 10 floor tile shop make flat, thick slurry wipe a seam 2. 20 厚 1:4 干硬性水泥砂浆。2. 20 thick 1:4 harsh cement mortar. 3. 素水泥浆结合层一遍3. Plain cement combining layer again 4. 拆除原面层至原地面垫层4. Remove the original surface to the original floor mat layer 5.5.9 水泥砂浆地面5.5.9 cement mortar on the ground
17、 1. 30 厚 1:2 干硬性水泥砂浆。1. 30 thick 1:2 harsh cement mortar. 2. 素水泥浆结合层一遍2. The slurry combining layer again 3. 拆除原面层至原地面垫层3. Remove the original surface to the original floor mat layer 5.5.10 塑料地板楼面5.5.10 plastic floor to floor 1. 3 厚塑料地板1. 3 thick plastic floor 2. 配套胶黏剂粘结。2. Adhesive form a complete
18、set of adhesives. 3. 建筑胶水泥腻子批嵌平整3. Plastic cement construction putty of embedded is flat and level 4. 20 厚 1:3 水泥砂浆找平，压实抹光。4. 20 thick 1:3 cement mortar leveling, compaction finishing. 5. 素水泥砂浆结合层一遍。5. Plain cement mortar layer again. 6. 拆除原面层至原楼板面层或现浇混凝土楼板6. Demolition of the original surface to th
19、e original floor surfaces or cast-in-situ concrete floor 5.5.11 陶瓷地砖防滑防水楼面Waterproof non-slip floor 5.5.11 ceramic floor tile 1. 10 厚地砖铺实拍平，水泥浆擦缝1. 10 floor tile shop make flat, thick slurry wipe a seam 2. 20 厚 1:4 干硬性水泥砂浆。2. 20 thick 1:4 harsh cement mortar. 3. 2 厚聚氨酯涂膜防水层，涂三边，四周卷起 200 高3. 2 thick
20、polyurethane coating waterproof layer, trilateral, rolled up around 200 high 4. 刷基层处理剂。4. Brush treatment at the local level. 5. 20 厚 1:2 水泥砂浆找平层。5. 20 1:2 cement mortar screed-coat thick. 6. 50 厚（最高处）C20 细石混凝土从门口处向地漏找坡0.5%，最薄处不小于 30厚，随打随抹。6. 50 (top) and thick C20 concrete with fine stones from the
21、 door to find slope 0.5% floor drain, the thinnest place not less than 30 thick, with playing with. 7. 素水泥浆结合层一道7. A plain cement combined with layer 8. 拆除原面层至原地面垫层或现浇混凝土楼板8. Remove the original surface to the original floor mat layer or cast-in-situ concrete floor 5.5.12 水泥砂浆楼面5.5.12 cement mortar
22、floor 1. 30 厚 1:2 水泥砂浆抹面压光1. 30 thick 1:2 cement mortar plaster calender 2. 素水泥浆结合层一道2. A plain cement combined with layer 3. 拆除原面层至原地面垫层或现浇混凝土楼板3. Remove the original surface to the original floor mat layer or cast-in-situ concrete floor 5.5.13 陶瓷地砖防滑楼面5.5.13 ceramic floor tile prevent slippery flo
23、or 1. 10 厚地砖铺实拍平，水泥浆擦缝1. 10 floor tile shop make flat, thick slurry wipe a seam 2. 20 厚 1:4 干硬性水泥砂浆。2. 20 thick 1:4 harsh cement mortar. 3. 素水泥浆结合层一遍3. Plain cement combining layer again 4. 拆除原面层至原楼面垫层4. The demolition of the original surface to the original floor cushion layer 5.5.14 乳胶漆内墙5.5.14 in
24、terior wall emulsioni paint 1. 乳胶漆面层1. The latex paint surface 2. 5 厚 1:0.5:2.5 水泥石灰膏砂浆找平2. 5 thick 1-0. 5 5 cement lime putty mortar leveling 3. 9 厚 1:0.5:3 水泥石灰膏砂浆打底扫毛或划出纹道3. 9 thick 1-0. 5:3 cement lime putty mortar render brooming or draw lines 4. 素水泥砂浆一道（内掺建筑胶）4. A plain cement mortar (mixed bu
25、ilding glue) 5.5.15 面砖墙面5.5.15 brick wall 1. 10 厚面砖，水泥砂浆嵌缝1. 10 thick brick, cement mortar joint 2. 5 厚 1:1 水泥砂浆加水重 20%建筑胶镶贴2. 5 thick 1:1 cement mortar water 20% heavier construction glue stick 3. 9 厚 1:3 水泥砂浆（内掺 3%超密聚合物防水剂）打底压实抹平3. 9 thick 1:3 cement mortar (water mixing 3% super dense aggregation
26、 technology) with base compaction 4. 素水泥砂浆一道甩毛（内掺建筑胶）4. A plain cement mortar to jilt MAO (mixed building glue) 5.5.16 石质板材墙面Sheet 5.5.16 stone walls 1. 30 厚 1:2.5 水泥砂浆，分层灌浆1. 30 thick 1:2. 5 cement mortar, layered grouting 2. 30 厚石质板材（背面用双股 16 号铜丝绑扎与墙面固定）水泥浆擦缝2. 30 thick stone plate on the back (wi
27、th twin 16 copper wire binding and metope) cement seam 5.5.17 轻钢龙骨矿棉板吊顶5.5.17 light steel keel mineral wool board ceiling 1. 轻钢龙骨主龙骨中距 1000，铝合金 T 型龙骨中距 600，横撑龙骨中距 5001. 1000 in light steel keel main keel, aluminium alloy 600 T keel, lateral brace keel in 500 2. 600X600 厚开槽矿棉装饰板2. 600 x600 thick slot
28、 mineral wool decorative board 5.5.18 铝扣板吊顶5.5.18 aluminous gusset plate condole top 5.5.19 混合砂浆顶棚5.5.19 mixed mortar ceiling 1. 表面喷刷乳胶漆1. Surface spray brush emulsioni paint 2. 5 厚 1:0.5:3 水泥石灰砂浆2. 5 thick 1-0. 5:3 cement lime mortar 3. 7 厚 1:1：4 水泥石灰砂浆3. 7 thick 1:1:4 cement lime mortar 4. 钢筋混凝土板底
29、面清理干净4. Reinforced concrete slab bottom surface is clean 5.5.20 保温顶棚5.5.20 insulation roof 1. 轻钢龙骨矿棉板吊顶1. Light steel keel mineral wool board ceiling 2. 70 厚单层钢丝网架立纤维岩棉板（A 级） ，保温板内斜插腹丝及板面附加锚固筋2. 70 thick monolayer steel wire rack made fiber rock wool board (grade A), insulation board in the oblique
30、abdominal silk and board face additional anchoring reinforcement 3. 建筑胶水泥砂浆墙体找平3. Plastic cement mortar wall leveling construction 4. 钢筋混凝土板底面清理干净4. Reinforced concrete slab bottom surface is clean 5.5.21 木龙骨塑料条形扣板吊顶5.5.21 wooden keel plastic gusset plate condole top bar 1. 40X50 吊顶木龙骨中距 4001. 40 40
31、0 x50 ceiling keel 2. 9 厚塑料条形扣板用木螺钉固定2. 9 thick strip plastic gusset plate with screws 5.5.22 铝合金格栅吊顶5.5.22 aluminum grille ceiling 1. 采用分格龙骨安装1. The frame keel installation 2. 40 高格栅，规格为 40X120X1202. 40 high grille, the specification is 40 x120x120 5.5.23 踢脚 15.5.23 kicking 1 1. 配套胶粘剂粘贴1. Supportin
32、g adhesive paste 2. 3 厚塑料地板上翻 1502. 3 thick plastic floor turn 150 3. 成品压条封边3. Product layering sealing side 5.5.24 踢脚 25.5.24 kicking 2 1. 17 厚 1:3 水泥砂浆1. 17 thick 1:3 cement mortar 2. 4 厚 1:1 水泥沙浆加水重 20%建筑胶镶贴2. 4 thick 1:1 to cement mortar water 20% heavier construction glue stick 3. 10 厚面砖，水泥浆擦缝3
33、. 10 thick brick, cement seam 5.5.25 踢脚 35.5.25 kicking 3 1. 配套胶粘剂粘贴1. Supporting adhesive paste 2. 3 厚塑料地板上翻 1002. 3 thick plastic floor turn 100 3. 不锈钢成品踢脚板3. Stainless steel products skirting board 5.5.26 地下水泵房及地下水池底板5.5.26 ground water pump room and underground tank bottom 1. 12 厚聚合物水泥砂浆防水层1. 12
34、 polymer cement mortar waterproof layer thick 2. 2 厚水泥基类无机防水涂料2. 2 thick cement base class inorganic waterproof coating 3. 钢筋混凝土结构自防水（P6）3. Since the waterproof reinforced concrete structures (P6) 4. 30 厚挤塑聚苯板保温层4. 30 thick extruded polystyrene board insulation layer 5. 原有地下基础及墙体进行基层清理5. The origina
35、l grass-roots clean-up underground foundation and wall 6. 土层6. The soil 5.5.27 地下水泵房及地下水池侧墙5.5.27 ground water pump room and underground pool side walls 1. 12 厚聚合物水泥砂浆防水层1. 12 polymer cement mortar waterproof layer thick 2. 2 厚水泥基类无机防水涂料2. 2 thick cement base class inorganic waterproof coating 3. 钢筋
36、混凝土底板结构自防水（P6）3. The reinforced concrete slabs from waterproof (P6) 4. 100 厚 C15 混凝土4. 100 thick C15 concrete 5. 素土分层夯实5. Soil layered compaction 5.5.28 地下室底板防水消防水池5.5.28 basement floor waterproof fire pool 1. 20 厚 1:2 水泥砂浆找平层1. 20 1:2 cement mortar screed-coat thick 2. 钢筋混凝土底板结构自防水（P6）2. The reinfo
37、rced concrete slabs from waterproof (P6) 3. 100 厚 C15 混凝土3. 100 thick C15 concrete 4. 素土分层夯实4. Soil layered compaction 5.5.29 地下室墙身防水消防水池5.5.29 basement wall waterproof fire pool 1. 20 厚 1:2 水泥砂浆找平层1. 20 1:2 cement mortar screed-coat thick 2. 钢筋混凝土结构自防水（P6）2. Since the waterproof reinforced concrete
38、 structures (P6) 3. 30 厚挤塑聚苯板保温层3. 30 thick extruded polystyrene board insulation layer 4. 原有地下基础及墙体进行基层清理4. Original underground foundation and wall body to clean up at the local level 5. 土层5. The soil 5.5.30 集水坑，排水沟5.5.30 sump, drain 1. 钢筋混凝土底板结构自防水（S6）1. Reinforced concrete floor structure since
39、the waterproof (S6) 2. 20 厚 1:2 水泥砂浆找平层2. 20 1:2 cement mortar screed-coat thick 3. 2 厚无机铝盐防水素浆3. 2 thick inorganic waterproof aluminum salt slurry 4. 20 厚无机铝盐防水砂分两次抹面，表面压光4. 20 thick inorganic aluminum salt waterproof sand two plaster, surface pressure light 5.5.31 消防泵房、楼梯间细石混凝土地面5.5.31 fire pump r
40、oom, stair, fine stone concrete ground 1. 30 厚 C15 细石混凝土随打随抹平1. 30 thick C15 concrete with fine stones along with screeding 2. 素水泥浆结合层一道2. A plain cement combined with layer 3. 地下室结构层3. The basement structure layer 5.5.32 水泥砂浆砂浆内墙面The metope inside the 5.5.32 cement mortar mortar 1. 刷内墙涂料1. Brush in
41、terior wall coating 2. 5 厚 1:2 水泥砂浆找平2. 5 thick 1:2 cement mortar leveling 3. 15 厚 1:3 水泥砂浆3. 15 thick 1:3 cement mortar 4. 地下室结构层4. The basement structure layer 5.5.33 水泥砂浆防水顶棚5.5.33 cement mortar waterproof roof 1. 表面喷刷乳胶漆1. Surface spray brush emulsioni paint 2. 12 厚聚合物水泥砂浆防水层2. 12 thick polymer
42、cement mortar waterproof layer 3. 2 厚水泥基类无机防水涂料3. 2 thick cement base class inorganic waterproof coating 4. 钢筋混凝土板底面清理干净4. Reinforced concrete slab bottom surface is clean 5.5.34 水泥砂浆顶棚5.5.34 cement mortar ceiling 1. 20 厚 1:3 水泥砂浆找平层1. 20 1:3 cement mortar screed-coat thick 2. 钢筋混凝土板底面清理干净2. The rei
43、nforced concrete plate bottom clean 5.5.35 水泥砂浆，高 1505.5.35 cement mortar, high 150 1. 10 厚 1:2 水泥砂浆抹面压光1. 10 thick 1:2 cement mortar plaster calender 2. 15 厚 1:3 水泥砂浆2. 15 thick 1:3 cement mortar 5.5.36 木质基层调和漆5.5.36 wood mixed paint at the grass-roots level 1. 木基层清理、除污、打磨等1. The wood base cleaning
44、, decontamination, polishing, etc 2. 刮腻子、磨光2. Blow be bored with child, and polished 3. 底油一遍3. The bottom oil again 4. 调和漆两遍4. The mixed paint twice 5.5.37 金属基层调和漆5.5.37 metal mixed paint at the grass-roots level 1. 清理金属面除锈1. Clean the metal surface rust removal 2. 防锈漆或红丹一遍2. The antirust paint or h
45、igh build red lead again 3. 刮腻子、磨光3. Blow be bored with child, and polished 4. 调和漆两遍4. The mixed paint twice 5.5.38 细石混凝土散水5.5.38 aproll of fine stone concrete 1. 40 厚 C20 细石混凝土，面上加 5 厚 1：1 水泥砂浆随打随抹光。1. 40 thick C20 concrete with fine stones, and five on the surface of thick 1:1 cement mortar increa
46、ses with the increasing play finishing. 2. 150 厚 3:7 灰土。2. 150 thick 3:7 lime soil. 3. 素土夯实，向外坡 4%3. The soil compaction, outward slope of 4% 5.5.39 花岗岩火烧板台阶5.5.39 granite fire board level 1. 20 厚花岗岩火烧板水泥擦缝1. 20 thick granite board blackened cement seam 2. 30 厚 1:4 干硬性水泥砂浆2. 30 thick 1:4 harsh cemen
47、t mortar 3. 素水泥浆结合层一遍3. Plain cement combining layer again 4. 60 厚 C20 混凝土台阶（厚度不包含踏步三角部分）4. 60 thick C20 concrete steps (thickness does not include the footfall triangle section) 5. 300 厚 3:7 灰土5. 300 thick 3:7 lime soil 6. 素土夯实6. Plain soil compaction 5.5.40 屏蔽处理5.5.40 block processing 配电间内墙，顶棚及地面均
48、做屏蔽处理，在内墙，顶棚及地做基层时均加钢丝网片，然后用铜丝带相互连接底部网片与接地网接通。Distribution room interior wall, ceiling and ground do block processing, in interior wall, ceiling and to do at the grass-roots level and steel wire mesh, and then connected with copper belt at the bottom of the mesh and grounding network connected. 5.5.
49、41 周边地面The ground around 5.5.41 1. 面层做法详地面做法表1. Detailed ground practice table surface approach 2. 100 厚 C15 细石混凝土垫层2. 100 thick C15 cushion layer of fine stone concrete 3. 20 厚挤塑聚苯板（B1 级）3. 20 thick extruded polystyrene board (B1 level) 4. 300 厚灰土4. 300 thick dust 5. 素土夯实5. Plain soil compaction 1、做法范围为主楼非地下室部分外墙以里 2m 范围内地面。1, scope of practice as the main building of basement exterior wall in 2 m within the scope of the ground. 2、需全部拆除范围内原有地面构造。2, to remove within the scope of the original floor structure.
