1、NH5 平台岗位描述（第一版） 附件 9348钻井常用词汇英汉对照表打捞工具和常用词语spear 打捞矛 back pressure 回压side wall core 井壁取芯 drill out cement 钻水泥塞casing scraper 套管清刮器 explosive 炸药mill 磨鞋 squeeze cement 挤水泥die stamp 铅印 fast line spooler 快绳排绳器pin tap 公锥 shallow gas 浅层气box tap 母锥 panels 面板packer 封隔器 bridge plug 桥塞openner 扩眼器 well kick an
2、d 50BBLs pits gain 井涌增量 50 桶junck sub 打捞杯 kelly guard 方钻杆保护接头fishing over shot 打捞筒 blow out 井喷cutter 割刀 guideline 导向绳blades 刀臂 guide rail 导轨pony D.C 短钻鋌 pick up weight 上提重量pup joint 短钻杆 sluck off weight 下放重量slick M.D.C 光滑防磁钻鋌 rotating weight 总重量fishing neck 打捞短节 max torque 最大扭矩perforate 射孔 rotating
3、HRS 纯钻井时间no accident 无事故 total BHA length 总 BHA 长度HRS on swivel 水龙头时间 check crown o matic 检查防碰天车below jar W.T 震击器以下重量 total BHA weiht 总 BHA 重量HRS on jar 震击器时间 held safety metting on rig floor 钻台举行安全会seal assembly 密封总成 wear bushing 抗磨补芯total mud cost 泥浆总消耗量 bridge crane of the BOP BOP 叉车centrifical p
4、ump 灌注泵 liner 尾管brine 饱和盐 washpipe packing 冲管盘根sub sea camera 水下电视 sand traps 沉沙池core barrel 岩芯筒 compensator 补偿器travly block 游车 crown block 天车drawworks 钻井绞车 stabilizer 扶正器port 左舷 starboad 右舷annurlar prevent 万能防喷器 choke/kill line 阻流和压井管线shear ram 剪切闸板 choke manifold 阻流管汇trip tank 计量罐 gas peak 气测值NH5
5、平台岗位描述（第一版） 附件 9348349plug back 打水泥塞 dart sub 投入式止回阀nozzle 水眼 jetter 喷射冲洗器boost line 加速管线 core point 取芯点marine swivel 水下水龙头 trip gas 后效气prepare 准备 after effect 后效break CIRC 短时循环 mud cleaner 泥浆清洁器degasser 除气器 desilter 除泥器desander 除沙器 prior/before 在-之前shale shaker 震动筛 helicopter 直升飞机gas cut mud 气侵泥浆 s
6、pecial tool 特殊工具open hole 裸眼 No.4 guide line brocken 四号导向绳断掉tubing 油管 fix 修理testing 测试 caving 垮塌plugged bit 泥包钻头 D.c twist off 钻鋌折断well off set 井口位移 tugger 气动绞车recover survey 回收测斜仪 picth 纵摇rig heading 平台首向后 sweel 涌wind speed 风速 wave 浪roll 横摇 heave 升沉visib 能见度 dir 方位钻井常用短语Last anchor on rack at 0600H
7、R六点最后一个锚上架Start of contract at 1530HR下午三点半合同开始End of contract at 0300HR早上三点合同结束Rig on tow平台拖航Rig arrived well location at 1000HR早上十点到达井位Run anchors and frist anchor on bottom at 1100HR抛锚。第一个锚 11 点到底Ballast rig to 70ft draft压载到 70 英尺deballast rig平台卸载adjust well location with pull No .1 and No.2 ancho
8、rs gainNH5 平台岗位描述（第一版） 附件 9348350拉 1 和 2 号锚调整井位anchor tension test No.3 and No4-ok1 和 2 号锚张力试验-OKwait slack tide等待平潮replace upper felly cock替换方钻杆上阀spuded time开钻时间arrived time到达井位时间drill 36“hole from 120m to 200m & pump 50bbls mud each connection and ream each connection once钻 36“井眼从 120 米至 200 米 ,每接
9、一拄前滑眼一次并泵入 50 桶泥浆open 17-1/2“hole from 250m to 500m用 17-1/2“钻头扩眼从 250 米至 500 米leak off test at 500m.MW 1.2SG leak off 625psi破裂试验.井深 500 米、泥浆比重 1.2SG.泄漏压力为 625PSIream hole from 450m to 500m倒划眼从 450 米至 500 米core drill from 1300m to 1320m取芯钻进从 1300 米至 1320 米collect/remove core and service core equipmen
10、t收集/甩下岩芯并包装处理sweep hole with 100bbl HI-VIS mud用 100 桶高粘泥浆清洗井slug the hole with viscous mud泵送一段稠泥浆进井pump 6000stks HI-VIS mud 泵 6000 冲高沾泥浆circulate and working on pipe循环并活动钻杆circulate and wash from 100m to 200m循环清洗 100 米至 200 井段circulate bottom up循环井底出来circulate for sample循环取样flow check at 2300m due t
11、o drilling break流量观察因钻至 2300 米时突变NH5 平台岗位描述（第一版） 附件 9348351circulate for flow check 循环观察circulate and condition mud循环处理泥浆reverse circulate反循环pooh no rotary and no drag起钻不用转盆也不拖挂run in W/26“ x 36“BHA tag seabad 117m.下 26“领眼钻头和 36“扩眼器至 117 米探海底泥面RIH to wipe trip下钻通井RIH to tag top of cement at 1000m下钻探
12、水能面在 1000 米处short trip over pull 50klbs短起过提 50 千磅make up new bottom hole assy组合新的下部钻具drop survey pump slug and POOH投测打重泥浆.起钻retrieve/return survey回收测斜仪inside BOP drill at casing shoe在套管鞋进行防喷演习POOH circ & fill annulars W/TR.TK.P no good. Suspect mud problems.W/pull out every 5 Stands&fill a time okW/
13、Pull out every 5 Stands&fill a time ok.起钻灌浆不正常,怀疑是泥浆问题.每起五柱灌浆-正常POOH due to change bit因要换钻头所以起钻POOH due to lost pump pressur supect washout D.C泵压下降起钻,怀疑钻鋌刺漏POOH due to plan change计划改变起钻POOH for changing bottom hole assy起钻更换下部钻具组合POOH wet pipe and no slug起钻喷泥浆因没打重泥浆POOH no rotary 起钻不转转盆NH5 平台岗位描述（第一版
14、） 附件 9348352POOH and tight hole at 2500m max over pull 100klbs起钻在 2500 米处遇阻最大过提 100 千磅slip and cut off drill line 110feet滑移切割钻井大绳 110 英尺RIH at casing shoe then service rig下钻至套管鞋后保养钻机POOH casing shoe adjust break&wait hole stabilize起钻至套管鞋待井稳定后调整剎带pull back 5 stands5“drillpipe and rick back derrick起出
15、5 柱 5“钻杆并立回井架attempt retreive9-5/8“wire bushing but fail试图回收 9-5/8“抗磨补芯没成功50bbls pit gain shut in well observe pressure 0-SIDPP 175psi SICP50 桶泥浆增量,关井后钻杆压力为 0,套管压力为 175psikill well as NHWOC,s requst按西部公司压井程序压井CIRC and COND .mud.CIRC out gas show from returns max gas 1700units循环处理泥浆,最大气测值为 1700 个单位D.
16、P hang off on L.P.R.CIRC.through wide open choke while W.T up mud钻杆悬挂在下闸板,循环通过全开阻流阀同时加重泥浆moniton will on trip tank 3 bbls gain in 2HRS在泥浆计量罐观察两小时有 3 桶的增量.circulate and inspect due to pressure lost 200psi循环检查因泵压下降 200PSIcirc through choke holding 600psi back press on annulars while WT up mud保持 600PSI
17、 套管循环压力通过阻流管汇同时加重泥浆bleed off shut in pressure 20bbls return still fiowing卸压后有 20 桶回流,井内依然有回流.stuck pipe at 2534m and work on pipe with 100kibs over pull fire jar max pull 500klbs free500klbs free.钻具卡在 2534 米上提下放活动钻具，过提 100 千磅震击器工作，最大上提 500 千磅解卡over pull 450klbs the D.P twist off and lost weight 280
18、klbs total 2999m in hole过提 450 千磅钻杆折断，失去悬重 280 千磅落鱼总长为 2999 米weld guide shoe onto 8-1/8“ overshot焊接 8-1/8“打捞筒和引鞋rig up pin tap RIH to top of fish and engage the fish -no succss and POOH组合公锥下钻打捞落鱼不成功，起钻work overshot onto fish w/max overpull 50klbs free & POOH打捞落鱼过提 50 千磅活动& 起钻NH5 平台岗位描述（第一版） 附件 93483
19、53observe well on trip tank.well static倒向泥浆计量罐观察井内稳定jump ROV and work for guide problems下放潜水器帮助处理导向绳问题attempt to re-establish guideline No.4试图回接 4 号导向绳ballast rig and pull anchors stable into 36“hole压船并拉锚对 36“井眼rig up run9-5/8“casing tools and running 9-5/8“casing安装下 9-5/8“套管的工具和下 9-5/8“套管pick up 9-
20、5/8“casing hanger and R/tool mack up and torque up lay out same组合 9-5/8“套管头和送入工具连接并上好扭矩然后甩下pick up casing shoe jiont and float M/U inspect ok RIH拉起套管鞋和浮阀单根并连接，检查好后下入井run stinger string下内管柱run 9-5/8“ casing fill mud for each 10 joints每下 10 根 9-5/8“套管灌满泥浆一次P/U and M/U 9-5/8“casing head joint continue
21、RIH W/5“drillpipe接好 9-5/8“套管头，继续用 5“钻杆送入井hanger off 9-5/8“casing 悬挂 9-5/8“套管M/U cment line to the unit and pressure test same 2000psi-ok连接水泥管线到固井泵并压力测试管线至 2000psi-OKpressure test casing 2000psi hold 10mins-ok压力测试套管至 2000PSI 并稳压 10 分钟-OKline up to cement unit & set cement plug as per phillips program
22、es管线连接到固井装置&按 phillips(作业者)程序打水泥塞back off running tools and POOH then break lay down same倒开送入工具起出卸掉甩下rig up run / pull B.O.P stack准备下/起防喷器组run TGB W/rig camera to seabed.land on seabed.inspect W/cemera appeared all ok.release R/tool用水下电视协助下永久性导向架。座在海底并检查合格后倒出送入工具inspect and repair B.O.P stack检查和修理防喷
23、器组S.C.R about choke line 100psi with 1.26M.with 30 spm and No.1 pump阻流管线的压力降是 100PSI。泵速为此 30 冲/分钟，泥浆比重为 1.26SG 用一号泵NH5 平台岗位描述（第一版） 附件 9348354B.O.P test as phillips,s request -ok.按 PHILLIPS 的要求进行防喷器组测试pressure test inside BOP gray valve and kelly upper/lower valve -ok压力测试方钻杆上下阀、钻杆内防喷器阀门-OKinspect and
24、 repair yllow / blue pod function test BOP -ok检查和修理黄/蓝盒并对防喷器组进行功能测试 -OKcrew working on moon pool and spider deck钻井班在月亮池和完井甲板工作pick up 3 joint risers and R/tool make up install L.M.R.P组合三根隔水管和送入工具并连接好插入总成.run stack slip pressure testn choke/kill line each 3 joint riser下防喷器组和隔水管并每三根试压一次pick up slip jo
25、int.rig up choke/kill goosnecks install rucker ring下伸缩节及组装阻流/压井的鹅颈管和支撑环节jump R.O.V to watch and check well head well放潜水器去观察井口状况良好land stack . Lock connector check with 30 klbs over pull -ok座封和连接井口并关连接器后过提 30 千镑-OKscope out slip jt pick up diverter and install same rig down BOP running tools拉出伸缩节内筒坐转
26、喷器以及甩下所有防喷器组的送入工具pull out diverter.slip joint.riser and BOPstack.起出转喷器.伸缩节.隔水管和防喷器组rotary torque 250amps on bottom 100amps off bottom钻具在井底钻盆扭矩为避免 250 安培,离开井底为 100 安培.No1pump for drilling and No2pump use for boost riser一号泵钻进,二号泵导向隔水管,增加隔水管处的上返速度.rig evacuat for typhoon平台撤离防台风first chopper land rig at
27、 pm1700HR下午 1700 第一班飞机到平台crew come back form SAN YA by nanhai211 boat at am0700HR早上 0700 人员从三亚乘南海 211 船回平台.常用英文缩略语L/D-lay down 甩下 HWDP-hight weight drill pipe 加重钻杆BHA-bottom hole assembly 下部钻具组合 T.G.B-temporary guide base 临时基板L/O-lay out 甩出 P.G.B-permanent guide base 永久性基板L.M.R.P-lower marining rise
28、r package 插入总成 AFT-after 船首NH5 平台岗位描述（第一版） 附件 9348355M/U-make up 上紧 FWD-forward 船尾SIDPP-shut in drillpipe pressure 关井钻杆压力 PPG-pound per gallon 磅/加仑P/U-pick up 上提 SG-specific gravity 克/立方厘米S/OFF-sluck off 下放 TBG-tubing 油管SICP-shut in casing pressure 关井套压 pres-pressure 压力CIRC-circulate 循环 AFT.-after 在
29、。 。 。 。 。后POOH-pull out of hole 起钻 surfaceline 地面管线COND-condition 调整 TT-total 总计RIH-run into hole 下钻 T.D-total depth 总井深CONT-continue 继续 TR.TK-trip tank 计量罐RTTS-retrievable test treat squeeze packer 可回收的测试封隔器 D.P-drill pipe 钻杆WT-weight 重量 D.C-drill collar 钻鋌BOP-blow out preventor 防喷器组 WOB-weight on
30、bit 钻压X.O-crossover 配合接头 RPM-rate per minute 转/ 分钟W.O.O-wait on order 等待命令 SPM-stroke per minute 冲/分钟D.S-dart sub 投入式止回阀接头 GPM-gallon per minute 嗧/分钟W.O.W-wait on weather 等待天气 hr-hour 小时F.S-float sub 浮阀接头 min-minute 分钟W.O.C-wait on cement 候凝 sec-second 秒B.S-bit sub 钻头接头 in-inch 英寸SIPT-shut in pressu
31、re test 关井求压 ft-feet 英尺SSTT-subsea test tree 水下试油树 gal-gallon 嗧assy-assembly 总承 bbl-barrels 桶csg-casing 套管 lb-pound 磅cmt-cement 水泥 klb-kilopound 千磅conn-connection 连接 jti-joints 根数IF-inner flat 内平 bttms-bottoms 井底FH-full hole 贯眼 B/U-bottom up 井底返上REG-regular 正规 TQ-torque 扭矩S.W-sea water 海水 ROT/TQ-rotary torque 转盆扭矩F.W-fresh water 淡水 STKS-stroks 冲数temp-temperaure 温度 V/V-valve 阀WD-water depth 水深
