1、【飞机维修中各类工具中英文对照】2014-07-04 扳手 Wrenches/套筒 Sockets开口扳手 Open End Wrenches 梅花扳手 Spline End Wrenches块扳手 Crowfoot Wrenches 开口/梅花扳手 Combination Wrenches内六角扳手 Hex Wrenches 平板棘轮扳手 Slab Ratchet棘轮扳手 Ratchet Wrenches 力矩扳手 Torque Wrenches管钳 Pipe Wrenches 活动扳手 Adjustable Wrenches六角套筒 Six Point Sockets 梅花套筒 Twelv
2、e Point Sockets万向套筒 Universal Sockets 转接头 Adaptor套筒接杆 Socket Extension 万向转接头 Universal Joint螺刀 Screwdrivers快速螺刀 Fast Screwdrivers 仪表螺刀 Electronic miniature Screwdrivers十字头螺刀 PILLIPS Screwdrivers 磁性螺刀 Magnetic Screwdrivers一字头螺刀 Flat Tip Screwdrivers 摇把 Speeders钳 Pliers尖嘴钳 Needle Nose Pliers 大力钳 Locki
3、ng Pliers保险丝钳 Safety Wire Twisters 鹰嘴钳 Adjustable Joint Pliers插头钳 Connector Plug 剥线钳 Wire Strippers鱼口钳 Combination Slip-Joint Pliers 卡环钳 Convertible Snap Ring Pliers剪线钳 Diagonal Cutters 压线钳 Wire Crimpers电气工具 Electronic Tools矿灯 Safety Lamb (Miners Lamb) 手电 Flashing Light对讲机 Interphone 电烙铁 Electronic
4、Iron耳机 Earphone 防静电手腕 Static Wrist电池 Battery 充电器 Charger扬声器 Speaker 电源插座 Receptacle电枪 Electronic Runner 电钻 Electronic Drills指挥棒 Flashing Emergency Light 超声波 Ultrasonic测量工具 Measuring Tools钢板尺 Steel Rulers 卷尺 Tape Rulers螺旋卡尺 Outside Micrometer 塞尺 Feeler (Thickness) Gauges量杯 Measuring Cup 游标卡尺 Dial Cal
5、iper表 Gauges 三用表 Multi Meter兆欧表 Meg Ohm Meter 杂项 Diversiform反光镜 Inspection Mirror 放大镜 Magnifier软杆双爪式机械手 Flexible Two_claw Pick Up Tool 软杆磁棒 Flexible Magnetic Pick Up Tool划刀 Utility Knife 刮刀 Scraper Knife剪刀 Snip (Scissor) 锯 Saw凿子 Chisels 錾子 Punch三脚架 Tripod (Spider) 铜榔头 Copper Hammer铁榔头 Iron Hammer 胶榔
6、头 Rubber Hammer弯勾 Hook 锉 File镊子 Nipper (Pliers) 销钉插拔工具 Pin Removal Tools气枪 Pneumatic Runner 气钻 Pneumatic Drills铆钉枪 Rivet Gun 注射器 Injector (Squirt)滑油加油车 Oil Cart 液压油加油车 Hydraulic Fluid Cart注油枪 Grease Gun 抹布 Dishcloth手套 Glove 绳索 Rope工具箱 Tools Kit 工具架 Tools Rack千斤顶 Jack 撬棒 Tommy Bar工作梯 Work Ladder 砂轮 G
7、rinding wheel砂纸 Sand paper 胶带 Adhesive Tape焊锡 Soldering Tin 拖把 Tow Bar发光背心 Flashing Vest 护目镜 Goggle (Blinkers)安全带 Life Belt(Safety Belt)增补两用扳手 CONBINATION SPANNER两用扳手套装 COMBINATION SPANNER SET加长型两用扳手 COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手 OPEN ENDED SPANNER WITH RING RATCHET梅花棘轮开口扳手套装 OPEN ENDED SPA
8、NNER WITH RING RATCHET SET两用棘轮扳手 COMBINATION RATCHET SPANNER两用棘轮扳手套装 COMBINATION RATCHET SPANNER SET1/4连 接物 ADAPTOR 1/4组合支架工具 COMBINATION HOLDING TOOL小型发光二极管 MINIATURE LED LAMP活动扳手 SINGLE OPEN ENDED SPANNER扳手套装 MAGNETO SPANNER SET单开口扳手/呆扳手 SINGLE ENDED OPEN JAW SPANNER双开口扳手 DOUBLE OPEN ENDED SPANNER
9、双开口扳手套装 DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手 PLARE NUT SPANNER（OPEN）半月型梅花扳手 HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN开口敲击扳手 OPEN ENDED SLOGGING SPANNER梅花敲击扳手 RING SLOGGING SPANNER高颈梅花敲击扳手 DEEP AFFSET RING S
10、LOGGING SPANNER直头梅花扳手 DEEP RING SPANNER（STRAIGHT PATTERN）延长管 EXTENSION TUBE爪型扳手 CROWFOOT SPANNER两用活头扳手 COMBINATION SWIVEL HEAD WRENCH活结 T 型扳手 SWIVEL HANDLE WITH SLIDING T套筒扳手 SOCKET WRENCH弯头套筒扳手 ANGLED SOCKET WRENCH双头套筒扳手 DOUBLE ENDED SOCKET WRENCH旋棒 TOMMY BAR分节旋棒 STEPPED TOMMY BAR3C 把手套筒扳手 SOCKET W
11、RENCH WITH 3C-HANDLET 型及磁性套筒扳手 SOCKET WRENCH WITH T-HANDLE AND MAGNET钩头扳手 HOCK SPANNER WITH LUG带销扳手 PIN SPANNER可调式两爪钩扳手 CALIPER FACE SPANNER WITH ADJUSTABLE1/4标 准六角套筒 HEXAGON SOCKET1/4加 长六角套筒 HEXAGON LONG PATTERN SOCKET棘轮扳手 RATCHETS套筒 SOCKETS套筒套装 SOCKETS SETS摩擦棘轮扳手 FRICTION RATCHETS冲击工具 IMPACT TOOLS
12、旋具头 BITS扭矩扳手 TORQUE WRENCHES1/4 梅花套筒 SOCKET UD PROFILE1/4 六角套筒星型套筒 SOCKET FOR PROTRUDING HEAD SCREWS1/4 一字，十字，星型，内六角旋具套筒1/4双向棘轮套筒扳手 1/4REVERSIBLE RATCHETT 柄棘 轮扳手 RATCHET WITH T-HANDLE手用棘轮头 HAND RATCHET WITHOUT HANDLE1/4 转 3/8 转换 接头 CONVERTER 1/4 TO 3/8T 型滑 动头手柄 TOMMY BAR WITH SLIDING T活动延长杆 FLEXIBLE
13、 EXTENSION通用延长杆 UNIVERSAL-JOINT EXTENSION1/4 四方 驱动连 接头 SQUARE-DRIVE COUPLER1/4 万向接头 UNIVERSAL JOINT活动头手柄 SWIVEL HANDLE套筒固定夹 SOCKET RAIL WITH MAGNETIC3/8 一字，十字，星型，内六角旋具套筒3/8 六角套筒 SOCKET HEXAGON 3/83/8 梅花套筒 SOCKET UD PROFILE塑料棘轮扳手 PLASTIC RATCHET旋具头接头 BIT ADAPTOR旋具头棘轮扳手 BIT RATCHET旋具头螺丝起子 BIT SCREWDRI
14、VER旋具头延长杆 BIT EXTENSION旋具头 SCREWDRIVER BITS风动套筒 IMPACT SOCKET风动套筒附件 ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄 HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手 FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON摩擦式四方棘轮扳手 FRICTION TYPE RATCHET WITH SQUARE RING安装扳手/尖尾扳手 CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM 扭力螺丝起子 TORQ
15、UE SCREWDRIVER HANDLE 0.6-5.4NM3C 一字螺丝 起子 3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C 十字 PH 螺丝起子 3C-SCREWDRIVER FOR CRUCIFORM HEAD PH3C 米字螺丝 起子3C 星型螺丝 起子3C 球头六角螺 丝起子5 件/6 件/7 件/155 件螺丝起子套装 SET FOR HEAD SCREWS电工螺丝旗子 ELECTRONIC SCREWDRIVER木柄螺丝起子 SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器 MAGNETIZER AND DEMAGN
16、ETIZER方刃锥子 SQUARE BLADED AWLT 型六角螺丝起子 HEXAGON SCREWDRIVER WITH T-HANDLET 型内六角扳手 HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手 HEXAGON SOCKET KEY加长内六角扳手 EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装 HEXAGON SOCKET KEY SETT 型星形螺丝起子 SCREWDRIVER WITH T-HANDLE曲柄螺丝起子 CRANKED SCREWDRIVER量规 GARGE车灯测电笔 CAR LIGHT TES
17、TER6-24 伏测电 笔 VOLTAGE TESTER 6-24V150-250 伏测电笔 VOLTAGE TESTER 150-250V钳子 3 件套装 PLIERS SET，3-PIECE万能手钳 48 件套 UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE小钢丝钳 SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳 POWER COMBINATION PLIERS塑料水口钳 SIDE C
18、UTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳 ELECTRICIANS SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳 LEVER-ACTION SIDE CUTTERS杠杆顶剪钳 LEVER-ACTION END CUTTING NIPPERS核头钳 TOWER PINCERS拨钉钳 PINCERS平头钳 FLAT NOSE PLIERS圆头钳 ROUND NOSE PLIERS直头尖嘴钳 LONG NOSE PLIERS弯头尖嘴钳电话钳 TEL
19、EPHONE PLIERS强力尖嘴钳 TRIPLE-FUNCTION PLIERS直口机修工钳 MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳 MECHANICS PLIER ANGLED PATTERN偏口机修工钳 MECHANICS PLIER OFFSET PATTERN30 度平圆机修钳 MECHANICS PLIER WITH 30电缆刀 CABLE KNIFE电工电缆刀 ELECTRICIANS CABLE KNIFE防静电专用钳子电子钳 ELECTRONIC PLIERS迷你电子钳 MINIATURE ELECTRONIC PLIERS防静电尖嘴钳
20、/防静电顶切钳/电子平头钳/电 子剪钳/ 防静电剪钳/电子剥线钳电缆剪钳 CABLE CUTTERS小型万用剪 SMALL UNIVERSAL SCISSORS万用电缆刀 UNIVERSAL CABLE KNIFE自动剥线钳 STRIPPING PLIERS ANTOMATIC剥线钳 STRIPPING PLIERS固定剥线钳 STRIP-FIX STRIPPING PLIERS剥线工具 WIRE STRIPPER高效剥线钳 HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳 PRECISION WIRE STRIPPER FOR DATA CABLES同轴电缆
21、剥线钳 WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳 INSULATING VARNISH STRIPPER剥线刀 WIRE STRIPPING KNIFE绝缘胶带 INSULATING TAPE压线钳 CRIMPING PLIERS锁把式压线钳 LOCK-GRIP CRIMPING PLIERS端子压线钳 WIRE END-SLEEVE PLIERS模块压线夹钳 MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳 MODULAR CRIMPING PLIERS精确压线钳 PRECISION CRIMPING PLIERS外卡簧钳（轴用）
22、EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X 型把 X-GRIP大力钳 LOCK-GRIP PLIERS平行钳夹大力钳 PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳 WIDE JAW LOCKING PLIERS滑行杆式大力钳 LOCK-GRIP SLIDE CLAMP固定大力钳 GRIP WRENCH FOR GLUEING机械工作台钳 MACHINE WORKBENCH CLAMP焊接大力钳
23、LOCK-GRIP WELDING CLAMP管子焊接大力钳 LOCK-GRIP TUBE WELDING CLAMPC 型大力钳 LOCK-GRIP C CLAMP水泵钳 UNIVERSAL PLIERS（7 种设置/5 种设置）水泵钳 WATER PUMP PLIERS特殊水泵钳 SPECIAL WATER PUMP PLIERS可调式高速管子钳 HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER高速曲口管子钳 HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳 MINI CHAIN PIPE WRENCH链钳 CHANIN PIPE
24、 WRENCH重型管子钳 STILLSON PIPE WRENCH断线钳 BOLT CUTTERS钳子套装（3 件/4 件/6 件/8 件）VDE 绝缘安全 电工工具 VDE INSULATED SAFETY TOOLSVDE 绝缘标 准符合 DIN EN 60900 IEC 60900：2004 以及 VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE 绝缘螺 丝起子 VDE SCREWDRIVER（一字/十字/ 米字/星型/ 内六角）VDE 绝缘起子套装电压传感器/电压测试器 VOLTAGE DETECTOR/TESTER绝缘扭力扳手 VDE TORQUE WREN
25、CH绝缘双向棘轮扳手 VDE REVERSIBLE RATCHET绝缘六角套筒 VDE SOCKET HEXAGONAL绝缘旋具头套筒 VDE SCREWDRIVER BIT SLCKETT 型绝缘 扳手 VDE T-HANDLE绝缘延长杆 VDE EXTENSION绝缘电工工具组套（3 件/8 件/14 件/108 件）VED 3C 绝缘手柄套筒扳手 VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手 VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET绝缘开口扳手 VDE SINGLE-ENDED OPEN SPANNERV
26、DE 绝缘钢锯 HACKSAW绝缘电缆刀 VDE CABLE KNIFE绝缘电缆剪 CABLE SHEARS棘轮式绝缘电缆剪钳 CABLE CUTTERSVDE 绝缘电缆 剪 VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强 力钢丝钳/ 绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直 头尖嘴钳/ 绝缘弯头尖嘴钳VDE 绝缘橡胶 垫 VDE RUBBER COVER SHEETVDE 绝缘电 工安全手套 VDE ELECTRICIANSS SAFETY GLOVES绝缘塑料夹 VDE PLASTIC CLAMPS车轮扳手 WHEEL WRENCHES十字
27、扳手 4 WAY WHEEL WRENCH撬棒 TYRE LEVER轮毂罩移除工具 HUBCAP RENOVING TOOS配重钳 BALANCE-WEINHT PLIERS制动弹簧钳 BRAKE-SPRING PLIERS闸线弹簧钳 PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷 BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE油壶 OIL CANS过滤器扳手 UNIVERSAL FILTER WRENCH皮带钳 PULLEY WRENCH阀门研磨机 VALVE GRUNDER阀门研磨工具 VALVE L
28、APPING TOOS油封钳 VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器 VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE活塞环钳 PISTON RING PLIERS软管夹钳 HOSE CLIP PLIERS电极拉马 BATTERY TERMINAL PULLER电池测试器 BATTERY TESTER火花塞套筒 SPARK PLUG SOCKET火花塞套筒扳手 SPARK PLUG SOCKET WRENCH火花塞刷 SPARK-PLUG BRUSH特殊尖冲凿 SPECIAL PIN PUNCH弹簧撑开器 S
29、PRING SPREADER球头拉拔器 UNIVERSAL BALL JOINT REMOVER通用罐 UMIVERSAL CANISTER防冻测试器 ANTI-FREEZE TESTER安装钳 INSTALLATION PLIERS吸盘 SUCTION LIFTER磁性拾取工具 MAGNETIC PICK-UP TOOL金属片切割器 NIBBER杠杆剪切机 LEVER-ACTION TIN SNIPS打孔钳 PUNCH PLIERS橡胶锤 RUBBER HAMMER塑料锤 PLASTIC HAMMER无后坐力锤 RECOILLESS HAMMER钳工球头锤 ENGINEERSS BALL P
30、EIN HAMMER钳工锤 ENGINEERSS HAMMER平面刮刀 FLAT SCRAPER三角空心刮刀 THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀 THREE-EDGED FLAT-GROUND SCRAPER密封刮刀 GASKET SCRAPER平锉 HAND FILE圆锉 ROUND FILE三角锉 TRIANGULAR FILE半圆锉 HALF-ROUND FILE锉类 6 件套装中心冲/凿/开口销冲 CENTRE PUNCHES/CHISELS/DRIFT PUNCHES钢锯 HACKSAW栓孔锯 KEYHOLE SAW小金属锯 SMALL M
31、ETAL SAW小 PUK 钢锯 PUK JUNIOR HACKSAWHOBBY 锯台钳/台虎钳 METALWORKING VICE（100/125/150mm）钢卷尺 STEEL TAPE MEASURE（3 米/5 米/8 米）阀塞尺 VALVE FEELER GAUGE塞尺火花塞塞尺 SPARK PLUG GAUGE螺纹规 THREAD GAUGE游标卡尺 POCKET VERNIER CALLIPER数显游标卡尺 DIGITAL CALLIPER划线器 SCRIBER镊子 TWEEZERS十字镊子 CROSSLOCK TWEEZERS螺钉取出器 BOLT EXTRACTOR断螺钉取出器
32、套装 SCREW EXTRACTOR SET机械螺母破开器 MECHANICAL NUT SPLITTER螺栓插入及取出器 STUD INSERTER AND EXTRACTOR丝锥 THREAD FILE管子割刀 PIPE CUTTER自动切割机 AUTOMATIC PIPE CUTTER链式切管机 CHAIN PIPE CUTTER虹吸扳手 SIPHON TRAP PLIERS钢丝刷 WIRE BRUSH锉刀清洁刷 FILE CLEANING BRUSH裁缝剪 TAILORS SCISSORS发光二极管井下检查灯 LED INSPECTION LAMP井下检查灯 INSPECTION LA
33、MP发光二极管工作灯 LED WORK LIGHT工程锤 ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤 ENGINEERSBALL PEIN HAMMER胡桃木备用手柄 SPARE HANDLE HICKORY工匠锤 JOINERSHAMMER ROTBAND-PLUS石匠锤 CLUB HAMMER双面石匠锤 DOUBLE FACED CLUB HAMMER ROTBAND-PLUS大锤 SLEDGE HAMMER大碎石锤 STONE SLEDGE HAMMER劈木锤 WOOD SPLITTING HAMMER铺路锤 PAVING HAMMER单板锤 VENEER HA
34、MMER磁性锤 MAGNETIC HAMMER ROTBAND玻璃装配工锤 GLAZIERS HAMMER炭化合金瓦锤 CARBIDE TILE HAMMER羊角锤 CLAW HAMMER电焊敲锤 SCALING HAMMER ROTBAND-PLUS无弹力安全锤 RECOILLESS HAMMER安全锤 SAFETY HAMMER SOFT-PLUS塑料锤 PLASTIC HAMMER橡皮锤 RUBBER MALLET HARD尼龙锤 NYLON HAMMER木锤 WOOLEN MALLET铜锤 COPPER HAMMER CLUB SHAPE铝锤 ALUMINIUM HAMMER ROTB
35、AND桶形铝锤 LEAD HAMMER SARREL SHAPE冷凿锤 COLD CHISEL HAMMER热凿锤 HOT CHISEL HAMMER平底压摸锤 SET HAMMER TOP PART压槽铁锤 TOP FULLER上型模锤 BOTTOM FULLER冲锤 PUNCH HAMMER镰刀锤 SCYTHE HAMMER锻工钳 BLACKSMITHS TONGS铆钉钳 RIVETTING TONGS锥型冲子/中心冲子/销式冲子 DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES自动中心冲子 AUTOMATIC CENTRE PUNCH WITH TIP冲子
36、组套 DRIFT PUNCH SET铆钉装配器 RIVET SETTER字母及数字冲子 LETTER AND NUMBER PUNCHES装配冲子 SETTING PUNCH撬杆 PRVBAR起钉器 NAIL FIFER OCTAGONAL撬棍 CROWBAR通用拉马 UNIVERSAL PULLER两爪拉马 PULLER 2-ARM PATTERN三爪拉马 PULLER 3-ARM PATTERN防腐蚀拉马 COROSTOP PULLER PATTERN快速拉马 QUICK-ACTION PULLER两爪液压拉马 UNIVERSAL 2-ARM PULLER拉马延长杆 EXTENSION F
37、OR PULLERS液压轴杆 HYDRAULIC PRESSURE SPINDLE三爪液压拉马 UNIVERSAL 2-ARM PULLER拉马套装 PULLER SET螺母劈开器 NUT SPLITTER液压螺母劈开器 NUT SPLITTER HYDRAULIC螺栓提取器 STUD EXTRACTOR轴承提取器 BALL BEARING EXTRACTOR滚珠轴承提取器套装 BALL BEARING EXTRACTOR SET内提取器 INTERNAL EXTRACTOR冲击轴承拉马 IMPACT BEARING PULLER汽缸拉马 CYLINDER LINER PULLER COMPL
38、ETE WITH SUPPORT BRACE分离拉马 SEPARATOR PULLER轴承分离器 BEARING SEPARATOR传动轴轴承拉马 DRIVE SHAFT BEARING PULLER分离器及拉马套装 SEPARATOR AND PULLER SET拉拔卡盘 PULLING CHUCK液压泵 HYDRAULIC PUMP液压手泵 HYDRAULIC HAND PUMP液压工具拉马 1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器 HYDRAULIC PRESS轮毂拉马 WHEEL-HUB PULLER传动轴拉马 DRIVE-SHAFT P
39、ULLER方向盘拉马 STEERING-WHEEL PULLER装配叉 DISMANTLING AND ASSEMBLY FORK球头拉拔器 BALL JOINT PULLER三爪机滤扳手 OIL FILTER HOOK弹簧撑 SPRING SPREADER塑料轴承安装套装 PROFESSINAL PLASTIC BEARING INSTALLATION SET法兰分离器 FLANGE SEPARATORS轨距测量器 TRACK ALIGNMENT GAUGE扳手 WRENCHES管子切割器 PIPE CUTTERS扩口工具 FLARING TOOLS弯管机 PIPE BENDERS管子工具
40、PLUMBING TOOLS铁皮剪/断线钳 TIN SNIPS/BOLT CUTTERS管子清洁设备 PIPE CLEANING EQUIPMENT弯管系统 PIPE BENDING SYSTEMSSNAP 管道扳手 PIPE WRENCH ECK-SNAP钢管切割器 PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器 PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器 RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES管子修边器 PIPE DEBURRING REAMER不锈钢
41、管修边器 PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES扩口工具套装 FLARING TOOL SET BOERDEX钢管扩口钳 EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机 PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机 PIPE BENDER WITH ROLLER弯管钳 PIPE BENDING PLIERS带滑轨的弯管钳 PIPE BENDING PLIERS WITH SLIDE RAIL带滚轴的弯管钳 PIPE BENDING PLIERS WITH ROLLER手动弯管机 MA
42、NUAL BENDING TOOL液压弯管机 HYDRAULIC PIPE BENDER手动液压弯管机 PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION电动液压弯管机 PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION管道矫直工具 PIPE STRAIGHTENING TOOL金属片弯边钳 SHEET METAL CRINPING PLIERS折边钳 SEAMING PLIERS快速夹取扳手 QUICK-CLAMP WRENCH夹管钳 GRIPPING PLIERS分级扳手 STEPPE
43、D KEY复合分级扳手 COMBINATION STEPPED KEY铁皮剪 TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS断线钳 BOLT CUTTER管道清洁软轴 FLEXIBLE PIPE CLEANING SHAFT排水管清洁器 DRAIN PIPE CLEANER工作台几工作桌 WORKBENCHES AND WORK TABLES工具车 TOOL TROLLEYS工具柜 TOOL CABINETS车间推车 WORKSHOP TROLLEYS抽屉柜/箱 DRAWER-CABINETS/BOXES衣柜/工作服柜 WARDROBE
44、S矮橱 LOWER CUPBOARD UNIT图纸夹 DRAWING HOLDER电源面板 PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台 HEXAGONAL WORKBENCH带抽屉工作台 WORKBENCH WITH DRAWER CABINET塑料抽屉插件 PLASTIC DRAWER INSERT工作桌推车 WORKSHOP TABLE TROLIEYS工作台 WORKBENCH带背板工作台坚固推车 TROUGH TROLLEY平板车 PLATFORM TROLLEY带手柄平板车 PLATFORM TROLLYE WITH HANDLE维护推车 SERVICE TR
45、OLLEY带工具箱车间推车 WORKSHOP TROLLEY WITH TOOL CHEST工具箱 TOOL CHEST存放斗 STORAGE TRAY卷纸架 PAPER ROLL HOLDER垃圾桶 WASTE BASKET移动架写字板 LECTERN WORKTOP存储盒 STORAGE BOXES带门库架 CUPBOARD WITH SHELVING WITH DOORS开敞式壁板 COMPLETE PANEL SYSTEM WITH SLOTTED PANELS存物柜 LOCKER WITH HINGED DOORS滑门橱 CUPBOARD WITH SLIDING DOORS电脑柜
46、COMPUTER CABINET桌上设备 DESK INSTALLATION移动电脑架 PC STAION MOBILE电脑车间组合 PC WORKPLACE COMBINATION更衣室条凳 CHANGING CUBICLE SEAT BENCH安全橱 SAFETY CUPBOARD衣橱 CLOTHES LOCKER带凳子的衣橱 CLOTHES LOCKER WITH SEAT BENCH消防员衣橱 FIREFIGHTERS CUPBOARD工具橱 TOOL CABINET移动式可回收物品垃圾收集箱 RECYCLING WASTE-COLLECTION CONTAINER MOBILE固定可
47、回收物品垃圾收集箱 RECYCLING WASTE-COLLECTION CONTAINER STATIONARY分类垃圾收集站 WASTE-COLLECTION STATION CONTAINER立式烟灰缸 STAND ASHTRAYOCHSENKOPF 系列斧头欧洲 ILTIS 型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS 特殊工具KLANN 汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备 TORQUE TESTER AND EQUIPMENT扭距倍增器 TORQUE MULTIPLIERS扭距角度指示器 TORQUE AN
48、GLE INDICATORS特殊 DREMO 工具 SPECIAL DREMO TOOLSDREMOMETER 系列扭力工具 DREMOMETER TOOLS扭距螺丝刀 TORQUE SCREWDRIVERS扭距扳手/扭力扳手 TORQUE WRENCHES电子扭距测试仪 ELECTRONIC TORQUE TESTERDKD 校准遵守 DKD 准则 3-7/3-8/DIN EN ISO 6789RAHSOL DREMOTEC 产品校准按照 DIN EN ISO 6789 标准迷你型扭距扳手 DREMOMETER MINIDREMOMETER 高强度铝合金扭距扳手 含：DREMOMETER 1
49、-12NM /10-100LBF.IN （塑料外表）DREMOMETER 6-30NM /50-270LBF.INDREMOMETER 8-40NM /70-350LBF.INDREMOMETER 20-120NM /15-90LBF.FTDREMOMETER 40-200NM /30-150LBF.FTDREMOMETER 50-300NM /35-220LBF.FTDREMOMETER 80-360NM /60-260LBF.FTDREMOMETER 110-550NM /80-405LBF.FTDREMOMETER 140-760NM /105-560LBF.FTDREMOMETER 520-1000NM /380-730LBF.FTDREMOMETER 750-2000NMDREMOMETER 1500-3000NMDREMOMETER 系列棘轮头 RATCHET HEADS DREMOMTER扭距限制接合器 TORQUE LIMIT UNIT转角仪 TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖范围 8-1000NM）开口扳子头 OPEN END RTTING梅花扳子头 RING END RTTING半开口梅花扳子头 FLARED END FITTING棘轮头 RATCHET HEAD四方头 FIXED SQUARE
