1、压力容器外观及几何尺寸检验报告Visual and Geometric Dimensions Examination Report of the Pressure Vessel产品编号 (Product No:) 序号No.检 查 项 目Examination Items标准规定Standard Stipulation实测结果Actual ExaminationResult检查结论Conclusion1 产品 总长 总高:Product Total Length Total Height (mm) 按图样及工艺技术要求 mm2 壳体内径: Inside Diameter of the Shel
2、l (mm) 按图样及工艺技术要求 mm3 壳体长度: Length of the Shell (mm) 按图样及工艺技术要求 mm4 壳体直线度: Straightness of the Shell (mm) 按图样及工艺技术及 GB150-98 规定 mm5 壳体圆度: Roundness of the Shell (mm) 按图样及工艺技术及 GB150-98 规定 mm6 冷卷筒节投料的钢材厚度:Thickness of the Cold-rolled Shell (mm) 按图样及工艺技术要求 mm7 封头成型后最小厚度:Min. Thickness of Formed Head (
3、mm) 按 JB/4737-95 规定 mm8 封头内表面形状偏差:Inside Surface of Head (mm) 按 JB/4737-95 规定9 封头直边纵向皱折深度:Buckling Depth of Head Skirt (mm) 按 JB/4737-95 规定10 A 类焊缝最大棱角度: Max. AngularDeformation at Category A Welds (mm) 按 GB150-98 规定 mm11 B 类焊缝最大棱角度: Max. AngularDeformation at Category B Welds (mm) 按 GB150-98 规定 mm1
4、2 A 类焊缝最大错边量:Max. Offset at Category A Welds (mm) 按 GB150-98 规定 mm13 B 类焊缝最大错边量:Max. Offset at Category B Welds (mm) 按 GB150-98 规定 mm14 焊缝最大咬边深度、长度/连续长度:Max. Undercut Depth and Length (mm) 按 GB150-98 规定单面坡口:One Side Groove (mm)15焊缝余高Reinforcement of Weld 双面坡口:Two Side Groove (mm)按 GB150-98 及 JB/T470
5、9-2000 和工艺技术要求16 焊缝外观质量:External Quality of Welds 符合图样及标准Conforming to Drawings and Standard17 角焊缝质量:Quality of Fillet Welds 符合图样及标准Conforming to Drawings and Standard18 端盖开合及联锁:Opening, Closing and Interlocking of Cover 符合图样及标准Conforming to Drawings and Standard19 法兰面垂直于接管或筒体: Flange FacePerpendicu
6、lar to Nozzle or Shell 符合图样及标准Conforming to Drawings and Standard20 法兰密封面质量:Quality of Flange Sealing Face 无径向贯穿伤痕No Radial Penetrating Scar21法兰螺栓孔与设备主轴中心线位置:Location Between Flange Bolt Holes and Main Axis of the Vessel对 中 跨 中Centering Straddle22 支座位置及地脚螺栓孔间距: SupportPosition and Interval of Fang B
7、olt Holes 符合图样及标准Conforming to Drawings and Standard23 管口方位及尺寸：Orientation and Dimensions of Nozzles 符合图样及标准Conforming to Drawings and Standard24 补强圈： Reinforcing Ring 符合图样及标准Conforming to Drawings and Standard25 主要内件位置及尺寸：Position andDimensions of Main Inner Parts 符合图样及标准Conforming to Drawings and
8、Standard26 容器内外表面质量：Quality of Insideand Outside Surfaces of the Vessel 符合图样及标准Conforming to Drawings and Standard27 铭牌安装位置及拓印图: Rubbing NameplateInstalling Position of the Nameplate 符合图样及标准Conforming to Drawings and Standard28 标志、油漆、包装：Stamping、Painting and Packing 符合图样及标准Conforming to Drawings and Standard结论 (Conclusion):质 量 总 检 验 员 检 验 员 年 月 Quality Examiner in Charge: Examiner: Date:
