1、Owners ManualKX100Karaoke ProcessorWARNING FOR YOUR PROTECTIONREAD THE FOLLOWING:KEEP THESE INSTRUCTIONSHEED ALL WARNINGSFOLLOW ALL INSTRUCTIONSThe apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as vases, shall be placed on the apparatus.CLEAN O
2、NLY WITH A DRY CLOTH.DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFAC-TURERS INSTRUCTIONS.DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.ONLY USE ATTACHMENTS/ACCESSORIES S
3、PECIFIED BY THE MANUFACTURER.UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third
4、 grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.Protect the power cord from being walked on or pinched particularly at plugs, convenience recep-tacles, and the p
5、oint where they exit from the apparatus.Use only with the cart stand, tripod bracket, or table specified by the manufacture, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.Refer all servicing to qualified service
6、personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.POWER O
7、N/OFF SWITCH: If the equipment has a Power switch, the Power switch used in this piece of equipment DOES NOT break the connection from the mains.MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where plug is not accessible, an all-pole mains switch with a cont
8、act separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building.FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse with same type and rating only.MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a diffe
9、rent line cord, attachment plug, or both, depending on the available power source at installation. Connect this equipment only to the power source indicated on the equipment rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel or equivalent.If conn
10、ected to 240V supply, a suitable CSA/UL certified power cord shall be used for this supply.The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangero
11、us voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owners manual.These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourse
12、lf. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturers warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.ELECTRO
13、MAGNETICCOMPATIBILITY This device complies with part 15 of the FCC Rules and the Product Specifications noted on the Declaration of Conformity. Operation is subject to the following two condi-tions: this device may not cause harmful interference, and this device must accept any interference received
14、, including interference that may cause undesired opera-tion. Operation of this unit within significant electromagnetic fields should be avoided. use only shielded interconnecting cables.IMPORTANT SAFETY INFORMATIONSAFETY INSTRUCTIONS NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.W
15、ARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.The cores in the mains lead are coloured in accordance with the following code:GREEN and YELLOW - Earth BLUE - Neutral BROWN - LiveAs colours of the cores in the mains lead of this appliance may
16、not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The core which is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow.The core which is
17、coloured blue must be connected to the terminal marked N or coloured black.The core which is coloured brown must be connected to the terminal marked L or coloured red.This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at ins
18、tallation. If the attachment plug needs to be changed, refer servicing to qualified service personnel who should refer to the table below. The green/yellow wire shall be connected directly to the units chassis.CONDUCTORWIRE COLORNormal AltL LIVE BROWN BLACKN NEUTRAL BLUE WHITEE EARTH GNDGREEN/YELGRE
19、ENWARNING: If the ground is defeated, certain fault conditions in the unit or in the system to which it is connected can result in full line voltage between chassis and earth ground. Severe injury or death can then result if the chassis and earth ground are touched simultaneously.DECLARATION OF CONF
20、ORMITYManufacturers Name: Harman Signal Processing Manufacturers Address: 8760 S. Sandy ParkwaySandy, Utah 84070, USAdeclares that the product: Product name: JBL KX100Product option: all (requires Class II power adapter that con forms to the requirements of EN60065, EN60742, or equivalent.)conforms
21、to the following Product Specifications:Safety: IEC 60065 -01+Amd 1EMC: EN 55022:2006EN 55024:1998FCC Part 15Supplementary Information:The product herewith complies with the requirements of the:Low Voltage Directive 2006/95/ECEMC Directive 2004/108/EC.RoHS Directive 2002/95/ECWEEE Directive 2002/96/
22、EC EC Regulation 278/2009 With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of 17 December 2008, this product is designed, produced, and classified as Professional Audio Equipment and thus is exempt from this Directive.Roger JohnsenDirector, EngineeringSignal Processing8760 S. Sandy Pa
23、rkwaySandy, Utah 84070, USADate: June 30, 2011European Contact: Your local JBL Sales and Service Office orHarman Signal Processing8760 South Sandy ParkwaySandy, Utah 84070 USAPh: (801) 566-8800Fax: (801) 568-7542If you want to dispose this product, do not mix it with general household waste. There i
24、s a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.Private household in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated coll
25、ection facilities or to a retailer (if you purchase a similar new one).For Countries not mentioned above, please contact your local authorities for a correct method of disposal.By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus p
26、revent potential negative effects on the environment and human health.IMPORTANT SAFETY INFORMATIONTable of ContentsSection 1 - Introduction 11.1 Defining the KX100 11.2 Contact Info . 2Section 2 - Getting Started 32.1 Quick Start . 32.2 Front Panel . 42.3 Rear Panel 52.4 Remote Control . 62.5 Progra
27、mming an External Remote . 72.6 Menus this will display a message indicating it is locked.13KX100Section 3Processing range is preset dependent) - This parameter adjusts the amount of delay which occurs before you begin to hear any repeats. This parameter is also adjustable from the front panel Delay
28、 knob.1. Karaoke Presets Range: 0 ms - 740 ms2. All Other Presets Range: 0 ms - 2500 ms Echo Repeat (0 - 99) - This parameter adjusts how many times the delay will be repeated. The higher the value of this parameter, the longer the delay effect will be heard before fading out. This parameter is also
29、 adjustable from the front panel Repeat knob.17KX100Section 3Processing lower settings create darker reverbs with more bass frequency emphasis. Reverb Level (0 - 99) - This parameter adjusts the overall level of the reverb effect. Use this parameter to add just the right amount of reverb effect to t
30、he source signal. Reverb Lowpass (8000 Hz - 16000 Hz) - This parameter adjusts the frequency of the reverb low pass filter. Lower values will allow the lower frequencies to pass through the reverb effect creating a fuller, darker reverb, whereas higher values will begin cutting off lower frequencies
31、, which can make a reverb sound thinner and sit better in a busy mix. Reverb Highpass (50 Hz - 1000 Hz) - This parameter adjusts the frequency of the reverb high pass filter. Lower values yield a darker sounding reverb, whereas higher values create a brighter sounding reverb effect.23KX100Section 3P
32、rocessing & Parameters3.14 Additional Input ParametersThere are some parameters which dont necessarily pertain to any of the processing algorithms previously listed, but do pertain to certain inputs. This sub-section covers these additional input parameters. VOD - Selects the VOD audio and video inp
33、uts as the source. DVD - Selects the DVD audio and video inputs as the source. BGM - Selects the BGM audio and video inputs as the source. AUTO - This option uses auto detecting to automatically select the source. The detector uses a priority system to determine which input has priority over the oth
34、ers. The order of priority is: 1. VOD, 2. DVD, 3. BGM (where 1 is highest priority and 3 is lowest priority). This means if signal is present at both the VOD and DVD inputs, the VOD input will be selected as the source as it has higher priority than the DVD input. When there is no longer signal pres
35、ent at the automatically selected input, the detector will automatically switch to the next priority down which contains signal. If there is no signal present at any inputs, no switching will occur. Mic Volume (Off, -47 dB - +6 dB) - This parameter allows you to adjust the mic volume via controlling
36、 the mic sources and effect. This parameter is also adjustable from the front panel Mic knob. Mic INI Volume (Off, -47 dB - +6 dB) - This parameter allows you to set the initial Mic Volume value via controlling the Mic sources and effect. This is the default value that the Mic Volume will be set to
37、each time the processor boots up. Mic Max Volume (Off, -47 dB - +6 dB) - This parameter allows you to set the absolute maximum limit in which the Mic Volume or Mic INI Volume can be set. Music Balance (L100 - Center - R100) - This parameter allows you to adjust the left/right balance of the music in
38、puts. Music Volume (Off, -47 dB - +6 dB) - This parameter allows you to adjust the volume of the music sources. This parameter is also adjustable from the front panel Music knob. Music INI Volume (Off, -47 dB - +6 dB) - This parameter allows you to set the initial Music Volume value. This is the def
39、ault value that the Music Volume will be set to each time the processor boots up. Music Max Volume (Off, -47 dB - +6 dB) - This parameter allows you to set the absolute maximum limit in which the Music Volume or Music INI Volume can be set. Effect Volume (Off, -47 dB - +0 dB) - This parameter allows
40、 you to adjust the volume of the effect independently. This parameter is also adjustable from the front panel Effect knob. Effect INI Volume (Off, -47 dB - +0 dB) - This parameter allows you to set the initial effect volume value independently. This is the default value that the Effect Volume will b
41、e set to each time the processor boots up or another preset is loaded. Effect Max Volume (Off, -47 dB - +0 dB) - This parameter allows you to set independently the absolute maximum limit in which the Effect Volume or Effect INI Volume can be set. 24KX100Section 3 Processing & Parameters3.15 Addition
42、al Output ParametersThere are some parameters which dont necessarily pertain to any of the processing algorithms previously listed, but do pertain to certain outputs. This sub-section covers these additional output parameters. Center Volume (-30 dB - +6 dB) - This parameter allows you to adjust the
43、volume of the Center Output. Center INI Volume (-30 dB - +6 dB) - This parameter allows you to set the initial Center Volume value. This is the default value that the Center Volume will be set to each time the processor boots up. Center Max Volume (-30 dB - +6 dB) - This parameter allows you to set
44、the absolute maximum limit in which the Center Volume or Center INI Volume can be set. Center Effect Volume (Off, -47 dB - +0 dB) - This will additionally adjust the center effect volume only while the main effect volume will still adjust Left, Right and Center. Sub Volume (-30 dB - +6 dB) - This pa
45、rameter sets the overall volume of the Sub Output. Sub INI Volume (-30 dB - +6 dB) - This parameter allows you to set the initial sub Volume value. This is the default value that the Sub Volume will be set to each time the processor boots up. Sub Max Volume (-30 dB - +6 dB) - This parameter allows y
46、ou to set the absolute maximum limit in which the Sub Volume or Sub INI Volume can be set. Crossover LRC Highpass (Off, 40 Hz-200 Hz) - This parameter sets the crossover frequency, sending the higher frequencies to the Left, Right and Center Outputs. This parameter can also be set to off, thereby by
47、passing the crossover. Crossover Sub Lowpass (40 Hz-200 Hz, Off) - This parameter sets the crossover frequency, sending the lower frequencies to the Sub Output. This parameter can also be set to off, thereby bypassing the crossover.3.16 UtilitiesThe remaining parameters can be found under the Utilit
48、ies menu and are described below.Utility ParametersThe KX100 contains the following Utility parameters: Remote Input (Int, Ext) - This parameter selects the remote control source, whether its the included JBL remote (Internal) or a third party remote control plugged into the EXT Remote Input (Extern
49、al). Contrast (1 - 16) - This parameter adjusts the contrast of the LCD Display. USB Audio Trim (-12 dB - +24 dB) - This parameter adjusts the signal level going from USB to the computer for recording purposes. LR EQ Link (On, Off) - When set to On, this parameter copies all Left EQ parameters over to the Right EQ channel. Modifying any Left or Right EQ parameters when link is set to On will adjust both Left and Right EQ channels.
