1、 PU 保温板脱模剂 MK-IF309一、性能：本品的主要成分是聚二甲基硅氧烷，具有极好的热稳定性和化学稳定性，脱模和隔离效果优异，不腐蚀模具，在模具表面不残存分解物，制品外观平滑美观，不影响制品的粘合性和受漆力，不污染模具。本品是纯有机硅的浓缩液，无毒无味，闪点高，安全。本品用石油醚或溶剂油稀释后使用，稀释倍率高。本品可连续脱模 5-8 次。二、主要用途：聚氨酯保温板、冷库板以及各种聚氨酯硬泡制品、防木材硬泡制品、玩具、工艺品制品的脱模。三、技术指标：外观：无色或浅黄色透明液体密度：0.82-0.85（D420）有效成分：100黏度：100-200 （mPa.s25 ）闪点：150稀释剂：芳
2、香、脂肪和氯化烃类，石油溶剂四、使用方法：将模具加温至 50以上。将脱模剂用溶剂或溶剂混合物稀释，并通过刷子或喷枪均匀涂于模具上，溶剂挥发后即可使用。使用的频率是基于模具的复杂程度和模制材料。为了模具表面的较好分散，建议使用混合溶剂稀释脱模剂。混合溶剂中至少含有 5 份异丙醇、10-20份氯化溶剂。石油醚或溶剂油稀释比例为 1：15-20五、包装：高强度塑料桶包装，每桶净重 25 公斤。200 升镀锌内趁塑料铁桶或塑料桶，净重 180 公斤。六、储存和有效期：在-20 50条件下保存在原装密闭容器中，有效期是 12 个月。超期，须经检验合格后方可使用。PU Insulation Board R
3、elease Agent1.PerformanceThis product main component is PDMS(Polydimethylsiloxane),has excellent thermal stability and chemical stability,good at demould and isolation effetiveness,non-corroding and without residual on the mould and good at mould surface, not influence the products adhesiveness and
4、paint, not pollution the mould.This product is concentrated solution of pure silicone, avirulent insipidity,high flashing point,safety.This product need to use the petroleum ether or solvent oil to dilution, high dilution ratio. And can continuously demould 5-8 times.2.Main ApplicationPolyurethane i
5、nsulation board、refrigeratory board and all kinds of polyurethane hard bubbles products、toy、 artware product mould.3.Technical IndexAppearance:colourless or light yellow transparency liquidDensity:0.82-0.85(D40)Effective constituent:100%Viscosity:100-200 (mPas/25C)Flashing Point: 150CDiluent:arema、f
6、at and chlorinated hydrocarbon,petroleum solvent4.Application Method:Warming the mould up to 50C. Use the solvent or the solvent mixture dilution the release agent, and use the brush or the spray gun to painting on the mould homogeneous,can use after the solvent volatilize.The frequency of use is ba
7、se on the complexity and material of the mould.In order to has a better disperse on the mould surface,suggest to use the the solvent mixture to dilution the release agent. The solvent mixture at least contain 5 part isopropyl alcohol and 10-20 part chlorinated solvent.The petroleum ether or the solv
8、ent dilution rate 1: 15-205.PackagingHigh strength plastic barrel, each barrel net weight is 25 kilogram.200 Litres galvanization lining plastic metal bucket or plastic bucket, net weight is 180 kilogram.6.Store and Indate.12 months under original sealed container during -20C50C。If pass the indate, need to use after the check out.
