1、Northstar Flat Roof Adhesive 北星平面屋顶用胶水,StarStuk Flat Roofing Adhesive is an industrial grade spray adhesive formulated specifically to bond flat roofing materials. StarStuk为工业级喷施胶水，专门用于平面屋顶材料的粘接。 It is a fast drying formula and has excellent high coverage. 它干燥快，覆盖度很高， It has good moisture and weathe
2、r resistance against extreme temperature exposure (110 Degrees C). 在极端气温环境（110C）下具有良好的抗湿气和抗高温性能。 Fast set up time 1-5 minutes with ample open time 20 minutes (depending on temps).干燥快，为1-5分钟，开放时间长，为20分钟（取决于现场温度） Northstar Spray System Advantage saving time and labor本系统能够节省时间和人工 80 sqm of two sided co
3、verage能够喷涂的面积（两面）达到80m Wind Uplift Report-Test Information具备抗风揭报告-测试数据 Simple installation attaching a dedicated hose and gun to a valve.安装简单，只需把专用软管和喷枪与阀门连接即可。,STARSTUK SPRAY SYSTEM PROCEDURE STARSTUK喷胶系统操作步骤,Dry time is approximately 1 to 5 minutes and open time is approximately 5 - 20 minutes aft
4、er application depending upon environmental conditions. 干燥时间约1-5分钟，开放时间约5-20分钟，视现场环境而定 Two sided application substrate and membrane对基体和卷材的表面喷胶 Spray about 10-24 cm from surface away from the surface, applying a uniform coat of adhesive.喷嘴与施工表面的距离为10-24cm，均匀地喷涂胶水层。 1 coats per side depending on need
5、每个面喷一道，视需要而定 Cross Spray Patterns 以十字交叉方式喷胶，即一个面横着喷，另一个面竖直喷。 Allow the adhesive to dry until tacky, adhere flat roofing material then apply sufficient pressure to ensure complete contact rolling the sprayed membrane onto the sprayed surface.让胶水自然干燥至略粘手，将喷好胶水的卷材滚放在喷好胶水的基面上使两者粘接，再用力压实确保其完全接触。,How to S
6、pray 喷胶,Cross Spray交叉喷胶,Tackiness Test 粘手测试,Roll Membrane with pressure压滚铺贴 卷材,APPLICATION REQUIREMENTS/PROCEDURES施工要求/程序,Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. 确保施工面的清洁、干燥，无尘土、油滴及松脱的涂料、蜡或油脂等 For best results, the temperature of the adh
7、esive and the surfaces being bonded should be between 16 degrees C and 27 degrees C, 为了达到最佳效果，胶水的温度和待粘接表面的温度应介于16-27C SS Flat Roof Adhesives can be used in colder or warmer climates, just need to test open time and drying time to ensure proper work pace.本胶水可以用于较冷或较热的气候环境，只需试验开放时间和干燥时间以保证合适的施工进度。 Use
8、 with adequate ventilation. 应在通风良好的环境下使用 We recommend shaking the canister well before using. 建议在使用前将胶水罐摇一摇 Attach and secure tightly the hose 6 ft. or 12 ft. (EH06 or EH12) to the spray gun with 9501 tip. 将6英寸或12英寸软管与带有喷头的喷枪连接好。 Attach the other end of the hose onto the canister. Make sure the hose
9、-valve connections are air tight. 将软管的另一端接到胶水罐上，确保连接处不漏气。 Open the valve on the canister slowly and fully. 缓慢打开胶水罐上的阀门至全开位置 Spray about 10 cm 22cm inches away from the surface, at 90, applying a uniform coat of adhesive (see picture on following page).喷头距施工表面为10-22cm，垂直喷胶，形成均匀的胶水层（见下页） Allow the adh
10、esive to dry until tacky, adhere flat roofing material then apply sufficient pressure to ensure complete contact.待胶水干燥至略粘手状态，铺贴卷材，再用力压实，确保表面完全接触。 Leave the hose and spray gun attached to the canister, leave the valve on the canister open. Do not disconnect the hose/gun from the canister. Close and l
11、ock the spray gun.保持软管和喷枪与胶水罐相连，保持胶水罐阀门开启。勿将软管和喷枪与胶水罐断开，关闭并锁住喷枪。 When change canisters immediately attach hose onto new Northstar Flat Roofing Adhesive canister, reducing potential for hose drying.更换胶水罐时，只需将软管迅速与新胶水罐连接，降低压力以使软管干燥,CLEAN SUBSTRATE清洁基面,Easy to attach gun and hose 易连接的喷枪和软管,(Brush, Vacu
12、um, Air compressor 毛刷、吸尘器、空压机),Maintenance and Storage维护和储存,If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner, acetone or toluene. 若喷头堵塞，则将喷头从喷枪上拧下来，用香蕉水、丙酮或甲苯等溶剂清洗。 ACR LEED compliant Northstar Adhesive Remover ACR LEED认可的北星胶水清除剂 Do not use a
13、pin on the spray tip orifice. 切勿使用大头针清理喷头孔 When canister is empty you will notice reduced spray pattern quality, spray out remaining adhesive until no adhesive or propellant (Air) comes out of the gun indicating that the hose and gun are clean.胶水罐变空时，会发现喷胶量变少，此时可将残余的胶水喷出，直至喷枪无胶水或空气喷出，显示软管和喷枪已清干净。 Ca
14、n change hose with full canister at this time. 这时可以换上带着新胶水罐的软管 Quickly change the gun to a new canister. 迅速把喷枪接到新罐上 Full or empty cans. Do not disconnect the hose/gun from the canister for storage. Close and lock the spray gun, leave the valve on the canister open. 无论胶水罐是满还是空，请勿将软管和喷枪从胶水罐上取下存放，关闭并锁上
15、喷枪，让胶水罐上的阀门保持开启状态。 Ready to use next opportunity just re-open the gun valve 此时系统处于备用状态，再打开喷枪阀门即可开始新的操作。 Canisters can be recycled: Collect the empties, pop the top, and sell as scrap metal another source of revenue, and reducing aerosol can waste.胶水罐可回收。收集空罐可作为非金属销售，增加收入来源并减少喷罐废物。,No spare parts不需备件 No repairs不需修理 Spray and Store for next use喷完就储存至下次使用 No Waste不产生废物,Simple cleaning 清洁简单,
