1、赛克 2009d 源代码(复制即可显示)（Mosaic 2009d source code (copy can be displayed)）table 1、传感器闭合回路, 微电脑过零触发控温, 功率大, 升温迅速, 温度精确稳定, 不受出风量影响. 2、气流量无极可调, 范围大; 数字式温度 / 风量显示, 温度 / 风量调节方便, 可以适应多种用途. 3、手柄装有敏感磁控感应器, 只要拿起手柄, 系统即迅速进入工作模式; 手柄放在手柄架上, 系统便会进入待机状态, 实时操作方便. 4、系统设有自动冷风功能, 可延长发热体寿命. 5、机身小巧, 占用工作台面小.功率消耗 td 700w td
2、 气流类型 td brushless fan, gentle wind, temperature range 100, -500, gas flow 120 L / min (max) display form LCD“ high grade blue screen LCD, “ noise “bgcolor=“ less than 40db handle, component length, 120cm“186x106x165mm“ weight 1.86kg“1. Hold the handle on the magnetic induction bracket. 2, according
3、 to the choice of appropriate wind mouth you have to remove the welding element size (Note: to make use of large diameter nozzle or not installed air nozzle is beneficial to blow out of the heat, and then the wind mouth set) to handle the air outlet, must check that there is no set close together, n
4、ext to no leak, otherwise it will seriously affect the removal of welding operation. 3. After soldering the soldering platform, the system is in a dormant state because the handle is resting on the handle rack, and the LCD window shows “sleep“. At this time, can work with parameter switching channel
5、s CH1, CH2, CH3 and set different channels (refer to “four parameters“ / 5. Remove the welding platform handle from the handle rack, the system will immediately enter the working state of the current channel, adjust to the appropriate amount of air, until the temperature is stable, you can work prop
6、erly. When warming up, “, “, often “bright“. The window shows “Real Temp“, which indicates the actual temperature. When the window does not show “Real Temp“, it indicates the parameters of the current setting. 6, if you need to stop working, put the handle on the handle rack, at this time the system
7、 automatically cut off the heating current, into the air supply cold air heater mode, when the temperature is lower than 100 degrees, the welding platform into a dormant state. 7 、 long term no operation, turn off the power switch. 1“, “channel switching“ and “parameter setting“ in the sleep state o
8、r the working state (the LCD window does not show “Off“). Parameter settings cannot be set when the window displays “Off“ during the cooldown. 2, in order to set the channel CH1 work parameters, for example, the channel CH2 and CH3 settings with the CH1. 1) air volume adjustment: according to the ne
9、ed to select suitable air volume, air volume range: 20100. Clockwise rotation of air volume increases, counterclockwise rotation of the air volume becomes smaller. Regulation time,The LCD window displays the current air volume value. 2) temperature regulation: according to the need to select the app
10、ropriate temperature, temperature range of 100 DEG 500 DEG Click “A.“ button, the temperature rise of 1 degrees celsius. If you press the “ button on at least 1 seconds, the release of “long“ is rapidly warming temperature until the desired temperature after button. B. click the “print“ button, redu
11、ces the temperature of 1 DEG C. If you hold it for at least 1 seconds, the release of “we“ rapidly reduce the temperature until the desired temperature after button. 3) data storage: only after adjusting the parameter value can the data be stored. Press and hold current to set the channel CH1 (about
12、 5 seconds) until the set parameter is blinking. If you set the prompt tone, ()“When the set parameter is blinking, the system will issue a long “beep“ sound, which indicates that the data is set successfully. Otherwise, if the data is not blinking, it means that the parameter value has not been sto
13、red. tone settings: In hibernation, hold the “CH1“ and “CH2“ buttons for about 2 seconds at the same time, switch the prompt tone to / without. When prompted, the LCD window displays “()“, when the debugging parameter or the calibration temperature, the system sends a short “beep“ sound, and after a
14、djusting the parameter value, the data storage is successful, and a long “beep“ is sent out.This machine adopts microcomputer intelligent control, can automatically detect the various key components failure situation, and through the display frequency is displayed to prompt the user to make correspo
15、nding processing, display symbols are as follows: “A.“ shows “-“, indicating that the air temperature is below 100 degrees, the solder stand is in standby mode, and the handle is resting on the handle frame. B. shows “real temp“, which indicates that the temperature is the actual temperature of the
16、welding table, otherwise the temperature is the setting temperature. C. shows “S - E“, which indicates that the sensor of the welding platform is defective and needs to be replaced with a heating element (heating material and sensor assembly). D. when working, show that the temperature is less than
17、50 degrees centigrade, and no longer heating up. It means that the heating unit of the welding platform may be damaged, and the heating element (heating material and sensor assembly) need to be replaced. When E. shows “()“, it indicates that the system has set the prompt tone, otherwise there is no
18、prompt. 1“, “sleep“, the window shows “sleep“, the transition from the working state to the sleep state, and the window shows “Off“. 2. Put the handle on the handle rack, the system enters the cooling stage, starts cooling with large air quantity, cools to 100 degrees, and then enters the dormancy state. 3. After the handle is removed from the handle rack, the system is awakened and immediately enters the working state.
