1、 TouchKit Manual foe WinCE v2.0.9 0TouchKitTouchScreen ControllerUser Manualfor Windows CEVersion: 2.0.9TouchKit Manual foe WinCE v2.0.9 1CONTENTCHAPTER 1. TOUCH PANEL CONTROLLER.21.1 CONTROLLER.21.2 SPECIFICATIONS AND FEATURES.3CHAPTER 2. INSTALLING TOUCHKIT.52.1 FOR WINDOWS CE 2.12 / 3.0.52.2 FOR
2、WINDOWS CE .NET STYLUS.62.3 FOR WINDOWS CE .NET AND CE 5.0 .16CHAPTER 3. CONFIGURATION UTILITY AND RIGHT BUTTON EMULATOR.203.1 FOR WINDOWS CE 2.12 / 3.0.203.2 FOR WINDOWS CE .NET .23TouchKit Manual foe WinCE v2.0.9 2Chapter 1. Touch Panel ControllerThis touch panel controller provides the optimistic
3、 performance of analog resistive touch panels for 4 wire, 5 wire and 8 wire models. It communicates with PC system directly through RS232, PS/2 or USB connector. Users can see how superior the design is in sensitivity, accuracy and friendly operation. The touch panel driver emulates mouse left and r
4、ight button function and supports operation systems including Microsoft Windows 95 / 98 / ME / NT4 / 2000 / XP / XP Tablet PC Edition, Windows CE 2.12 / 3.0 / .NET, Linux, iMac and DOS.1.1 ControllerInterface RS232 USB PS/24-wire Ready Ready Ready5-wire Ready Ready Ready8-wire Ready Ready ReadyCapac
5、itive Ready Ready XTable 1. Controllers match with different interfacesTouchKit Manual foe WinCE v2.0.9 31.2 Specifications and FeaturesSpecificationsPower requirements +5VDC ( Maximum 100mA, typical 70mA, 50mV peak to peak maximum ripple )Operating temperature 0 to 50 Storage Temperature -40 to 80
6、Relative Humidity 95% at 60 Protocol RS232 Model: 9600 bauds, None parity, 8 data bits and 1 stop bit USB Model: USB 1.1 Low speedPS/2 Model: PS/2 mouse Resolution 2048 X 2048Report rate RS232 Model: Max. 160 points/sec USB Model: Max. 160 points/secPS/2 Model: Max. 140 points/secResponse time Resis
7、tive: Max. 35 msCapacitive: Max. 20 msPin out definition 4 wire model: X+, Y+, X-, Y-5 wire model: UL, UR, COM, LR, LL8 wire model: X+, X+ref, Y+, Y+ref,X- , X-ref, Y-, Y-refPanel resistance 4, 8 wire resistive model: 200 900 ohm( pin to pin on the same layer )5 wire resistive model: 50 200 ohm( pin
8、 to pin on drive layer )Regulatory Approvals FCC-B, CETable 2. Specifications for TouchKit controllerTouchKit Manual foe WinCE v2.0.9 4FeaturesCalibration Fast full oriental 4 points position Compensation Accuracy 25 points linearity compensation.Draw Test Position and linearity verificationLanguage
9、 Support 10 languages for WindowsAdvanced Feature 1. Support monitor / display rotation2. Support multiple monitor / display3. Support QVGA and Half-VGA function4. Support edge compensation5. Support constant touchController Setting 1. Support multiple controllers2. Dynamical add / remove controller
10、s3. Change Controller interface without reboot.Mouse Emulator 1. Right / Left button emulation2. Normal / Click on touch / Click on release mode3. Auto right buttonSound Notification 1. Sound option (No Sound / Touch Down / Lift Up)2. Frequency adjustment3. Duration adjustmentDouble Click 1. Configu
11、rable double click speed 2. Configurable double click areaOS support 1. Windows 95 / 98 / ME / NT4 / 2000 / XP /Windows XP Tablet PC Edition2. Windows CE 2.12 / 3.0 / .NET3. Linux ( RedHat / Fedora / Mandrake /Suse / YellowDog )4. iMac. OS9.x / OSX5. MS-DOS:Support display resolution: 320x200, 640x2
12、00, 640x350, 640x480, 800x600, 1024x768 and 1280x1024 COM port support 1. Support COM 1 COM 256 for Windows and Linux2. Support COM 1 COM 8 for DOSTable 3. Features for TouchKit softwareTouchKit Manual foe WinCE v2.0.9 5Chapter 2. Installing TouchKitTouchKit is software, which contains drivers, conf
13、iguration and right button utilities of the touch panel controllers for RS232 and USB on x86 CPU and Windows CE operation system. The two utilities are as follows: Configuration supportThe calibration and draw test of touch panel are done by this support. Right button support This is utility for emu
14、lating the right and left button of mouse through controlling touch panel. Users can toggle between right or left mouse buttons by this utility. 2.1 For Windows CE 2.12 / 3.0There are totally five files in the TouchKit for Windows CE directory.Follow these steps to install TouchKit for Windows CE.To
15、uchKit.dll - driver Touch32ex.dll - specific dynamic linking library TouchTray.exe - right mouse supportTouchKit.exe - Configuration UtilityTouchKit.reg - information that will be added to registry 1. Make sure that Windows CE has the driver of serial ports.2. While building Windows CE, users have t
16、o assign TouchKit.dll, Touch32ex.dll, TouchTry.exe and Touchkit.exe to appropriate directory.3. Add some registry value as the content of TouchKit.reg.4. Now, build Windows CE with this touch panel driver and utilities. Note: TouchTray.exe is the file of the Right Mouse Utility. It has to be started
17、 with computer booting. So, put this file to appropriate directory to satisfy this specific request.Now, users can boot this Windows CE version on specific device. The right mouse button utility will be emulated while computer booting and the touch panel driver is also ready.TouchKit Manual foe WinC
18、E v2.0.9 62.2 For Windows CE.NET StylusThere are two driver package versions and showed as below:Use CE.NET bundle calibration utilityUse Stylus dedicated configuration utility.USB interface driver installation with CE.NET bundle calibration utility. File List:USBPort.dll - USB touch screen driverTo
19、uchp.dll - USB touch screen driverCalibration.exe - provide a program of calibration (Programmer could choose the path while building the image of CE platform. This program is not necessary for CE.NET)Note: Users select the UHCI or OHCI USB Host Controller driver into the platform, which supported b
20、y the target device, and check the USB mouse can go well at the same port.Select the Touch Display stylus into the platform. Users can see:“CatalogCore OSDisplay based devicesShell and User InterfaceTouch DisplayStylus”Select the Mouse into the platform. Users can see:“CatalogCore OSDisplay based de
21、vicesShell and User InterfaceMouse”TouchKit Manual foe WinCE v2.0.9 71. Create a sub-folder “CEDB” under C:2. Copy files USBPort.dll and Touchp.dll to the directory.3. Launch platform builder and open the platform workspace.4. Edit the PROJECT.BIB in the Parameter View of Platform Builder.5. Add the
22、se two lines in Modules:usbport.dll C:CEDBusbport.dll NK SHtouchp.dll C:CEDBtouchp.dll NK SHTouchKit Manual foe WinCE v2.0.9 86. Edit the PROJECT.REG in the Parameter View of Platform Builder.7. Add these lines for registry:HKEY_LOCAL_MACHINEHARDWAREDEVICEMAPTOUCH“DriverName”=”Touchp.dll”“Calibratio
23、nData”=”102,102 1945, 102 1945,1945 102,1945”“BCLEFT”=dword:64“BCRIGHT”=dword:64“BCTOP”=dword:64“BCBOTTOM”=dword:64Then copy the following sentences to the PROJECT.REGHKEY_LOCAL_MACHINEDriversUSBLoadClients14371_10_0_0255_255_255USB_TOUCH_Driver“DLL”=”USBPort.dll”HKEY_LOCAL_MACHINEDriversUSBLoadClie
24、nts14371_20_0_0255_255_255USB_TOUCH_Driver “DLL”=”USBPort.dll”HKEY_LOCAL_MACHINEDriversUSBLoadClients4660_10_0_0255_255_255USB_TOUCH_Driver “DLL”=”USBPort.dll”HKEY_LOCAL_MACHINEDriversUSBLoadClients3823_10_0_0255_255_255USB_TOUCH_Driver “DLL”=”USBPort.dll”HKEY_LOCAL_MACHINEDriversUSBLoadClients3823_20_0_0255_255_255USB_TOUCH_Driver“DLL”=”USBPort.dll”TouchKit Manual foe WinCE v2.0.9 98. After building the image of CE.NET and load it to hardware platform. Users can use the stylus to do the calibration, which can be found in the control panel.
