1、Symantec NetBackup Appliance 安装配置指南目 录一、Appliance IPMI 远程管理卡配置 .31.1 关于 IPMI31.2 IPMI 配置 3二、扩展柜安装 52.1 硬件连接 .53.2 添加扩展柜 .7三、Appliance 重灌系统 .92.1 设定系统引导 .92.2 系统安装过程 .11四、Appliance 初始化安装 144.1 初始化配置 .144.2 检查安装配置 .20一、Appliance IPMI 远程管理卡配置1.1 关于 IPMIIPMI 是 Appliance 设备的远程管理控制卡，通过 IPMI 可以进行远程控制操作比如开机
2、关机、用 ISO 重新安装操作系统、查看基本的硬件信息等。1.2 IPMI 配置1、 启动 Netbackup Appliance5220 设备；2、 按 F2 键进入 setup 配置菜单；3、 等待片刻，出现 Symantec 的 Logo；4、 导航到 Server Management，选择“BMC LAN Configuration”并回车5、 在 RMM3 LAN Cconfiguration 选项中，将 IP source 由 DHPC 改为 Static，在 IP address、Subnet mask、Gateway IP 中分别输入 IP 地址、子网掩码及网关6、按 F10
3、 保存退出7、打开浏览器输入配置的 IP 地址尝试登陆 IPMI；默认用户名及密码是sysadmin/Pssw0rd二、扩展柜安装注意：扩展柜安装可以在系统重灌之前或者之后进行；但是建议在重灌之前安装。初始化过程将自动创建 dedup disk pool；如果初始化完成之后再添加扩展柜，需要手动创建dedup disk pool。2.1 硬件连接注意：将主柜 SAS 连接线分别接入扩展柜的 IN 口；扩展柜的 OUT 口用于连接第二个扩展柜的 IN 口。连接图示（一个扩展柜）连接图示（两个扩展柜）注意：开启 Appliance 的时候先开扩展柜 2-3 分钟后，再开主柜。3.2 添加扩展柜1、
4、用 SSH 登录到 Appliance 命令行菜单注意：如果采用 SecureCRT 连接工具，可能要修改 Authentication 认证方式为 Keyboard Interactive，否则系统将拒绝您登录；如下2、转到 manage-storage 菜单，输入 show，列出当前的存储信息，如下可以看出 Uni_2 是扩展柜，状态为 New Available;nb-appliance.Storage show-Device | Total | Unallocated | Status -Appliance Operating System | 930.38 GB | - | In U
5、se Base Unit Storage (unit_1) | 4.5429 TB | 4.5419 TB | In Use Expansion Unit Storage (unit_2) | 35.470 TB | - | New AvailableNOTE: The name that appears in () (ex: unit_1) is the device name. Use the appropriate device name while issuing the commands to manipulate the storage.-Partition | Total | A
6、vailable | Used | %Used-AdvancedDisk | 0 GB | 0 GB | 0 GB | 0%Deduplication | 0 GB | 0 GB | 0 GB | 0%Unallocated | 4.5419 TB | - | - | -3、使用 Add 命令将扩展柜添加到系统nb-appliance.Storage Add - Info Following expansion units can be added:- Info unit_2nb-appliance.Storage Add unit_2- Info Checking the type of t
7、he unit_2 device.- Info Checking the state of the unit_2 expansion unit device storage.- Info Initializing unit_2 expansion storage.- Info Configuring unit_2 expansion unit storage.- Info Adding unit_2 expansion unit storage space to Unallocated space.- Info Succeeded.4、用 show 命令检查扩展柜是否已经被系统正常识别nb-a
8、ppliance.Storage show-Device | Total | Unallocated | Status-Appliance Operating System | 930.38 GB | - | In UseBase Unit Storage (unit_1) | 4.5429 TB | 4.5419 TB | In UseExpansion Unit Storage (unit_2) | 35.470 TB | 35.470 TB | In UseNOTE: The name that appears in () (ex: unit_1) is the device name.
9、 Use the appropriate device name while issuing the commands to manipulate the storage.-Partition | Total | Available | Used | %Used-AdvancedDisk | 0 GB | 0 GB | 0 GB | 0%Deduplication | 0 GB | 0 GB | 0 GB | 0%Unallocated | 40.012 TB | - | - | -三、Appliance 重灌系统2.1 设定系统引导1、打开浏览器登录到 IPMI 远程管理界面；2、导航到”R
10、emote control”，点击”Lauch console”打开远程控制台；注意：该 Console 需要 JAVA 支持，请确保电脑已经安装。3、打开控制台，选择”Device”Redirect ISO”，重定向 ISO 安装镜像；4、浏览并选择安装镜像5、按 F10 保存并退出2.2 系统安装过程1、系统重启过程中，按 F6 进入启动菜单选项2、 、选择”Virtual CDROM”，回车引导系统3、选择安装 Install 进行安装；4、安装过程无需人工干预，直至安装完成；安装时间大概 1-2 小时。四、Appliance 初始化安装4.1 初始化配置初始化过配置包括网络设定、时区时
11、间设定、设备角色（mastermedia server）设定等。1、 Appliance 默认 IP 地址为 192.168.1.1；将电脑直连到 eth0 口即可用浏览器登录，进行初始化配置2、点击“Setup Appliance”3、 NetBackup Appliance 共有 6 个 NIC，在此我们将 eth1-eht5 做绑定以增加网络带宽；默认绑定模式为 Balance-alb，该模式不需要在交换机端作额外的配置。输入 IP 地址及网关，在 NIC 栏选择 eth1-eth5,Bond Mode 为 blance-alb，然后点击 Add4、在 Default Gateway 栏
12、中输入网关，然后点击 Add网络设定之后可以进去 OS 检查网卡绑定及 IP 地址，如下nb-appliance:/etc/sysconfig/network # more ifcfg-bond0BONDING_MASTER=yesBONDING_MODULE_OPTS=mode=balance-alb miimon=100BONDING_SLAVE_0=eth1BONDING_SLAVE_1=eth2BONDING_SLAVE_2=eth3BONDING_SLAVE_3=eth4BONDING_SLAVE_4=eth5BOOTPROTO=staticDEVICE=bond0ETHTOOL_O
13、PTIONS=IPADDR=10.9.6.10MTU=NETMASK=255.255.255.0NETWORK=REMOTE_IPADDR=STARTMODE=autoUSERCONTROL=nonb-appliance:/etc/sysconfig/network #路由信息查看nb-appliance:/etc/sysconfig/network # more routesdefault 10.9.6.254 - -5、时区时间设定；输入 NTP 时钟服务器的 IP 地址，或者手工指定时区和时间6、修改密码7、 Appliance 角色设定。根据实际情况设定该设备的角色；在此我们选择为 M
14、aster Server8、开始初始化过程；该过程将持续 5 分钟左右，并且将重启相应的服务在初始化过程中，将进行如下配置：Stopping NetBackup processesPerforming Deduplication Engine cleanupCreating basic NetBackup configuration on appliance szbaksrvReconfiguring NetBackup databasesConfiguring NetBackup logging on appliance szbaksrvStarting NetBackup processe
15、s on appliance szbaksrvWaiting for NetBackup processes to startUpdating CLI views of appliance szbaksrvUpdating client install media for appliance szbaksrvStopping NetBackup processesPerforming Deduplication Engine cleanupCreating basic NetBackup configuration on appliance szbaksrvReconfiguring NetB
16、ackup databasesConfiguring NetBackup logging on appliance szbaksrvStarting NetBackup processes on appliance szbaksrvWaiting for NetBackup processes to startSetting Catalog storage partition size to 930.3828125 GB.Starting NetBackup processes. (2 min approx)Creating Deduplication DiskPool dp_disk_szb
17、aksrv and Storage Unit stu_disk_szbaksrv.Creating AdvancedDisk DiskPool dp_adv_szbaksrv and Storage Unit stu_adv_szbaksrv.Configuring live update for NetBackup clientsSetting NetBackup retention levels for backup imagesConfiguring NetBackup tape media settingsConfiguring tape libraries of appliance
18、szbaksrv, if anyUpdating CLI views of appliance szbaksrvUpdating client install media for appliance szbaksrvExporting NFS share szbaksrv:/inst/client for UNIX based NetBackup client installation.Exporting CIFS share szbaksrvclient for Windows based NetBackup client installation.Initial configuration
19、 of the NetBackup appliance is complete.Appliance szbaksrv has been configured as master appliance.Deduplication storage unit stu_disk_szbaksrv is ready for use as storage destination.Setup Complete.Running Sanity tests on Master Appliance.Checking if installation is successful . OKChecking if SSH i
20、s enabled . OKChecking if hostname is set . OKChecking if IP address is set . OKChecking if appliance user accounts exists . OKChecking if required packages are installed . OKChecking if NetBackup is configured and running . OKChecking if storage units and diskpools have been created . OKChecking if
21、 SLPs have been created . NAChecking if required NetBackup policies have been created . NAChecking if OpsCenter is configured and running . OKChecking test backup and restore operations . OKExpiring test backup images and deleting test policy . OKChecking IPsec setup on the box . NOT CONFIGUREDCompl
22、eted running tests on the appliance.SELF TEST RESULT : PASS4.2 检查安装配置初始化完成之后，可以登录命令行检查配置情况1、网络设定之后可以进去 OS 检查网卡绑定及 IP 地址，如下nb-appliance:/etc/sysconfig/network # more ifcfg-bond0BONDING_MASTER=yesBONDING_MODULE_OPTS=mode=balance-alb miimon=100BONDING_SLAVE_0=eth1BONDING_SLAVE_1=eth2BONDING_SLAVE_2=eth
23、3BONDING_SLAVE_3=eth4BONDING_SLAVE_4=eth5BOOTPROTO=staticDEVICE=bond0ETHTOOL_OPTIONS=IPADDR=10.9.6.10MTU=NETMASK=255.255.255.0NETWORK=REMOTE_IPADDR=STARTMODE=autoUSERCONTROL=nonb-appliance:/etc/sysconfig/network #/home/maintenance # ifconfigbond0 Link encap:Ethernet HWaddr 00:1E:67:2E:B3:E5 inet add
24、r:10.9.6.10 Bcast:10.9.6.255 Mask:255.255.255.0inet6 addr: fe80:21e:67ff:fe2e:b3e5/64 Scope:LinkUP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1RX packets:11 errors:0 dropped:0 overruns:0 frame:0TX packets:657 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:0 RX bytes:2160 (2.1
25、 Kb) TX bytes:39930 (38.9 Kb)eth0 Link encap:Ethernet HWaddr 00:1E:67:2E:B3:E4 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0inet6 addr: fe80:21e:67ff:fe2e:b3e4/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:669 errors:0 dropped:0 overruns:0 frame:0TX packets:5
26、61 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000 RX bytes:87040 (85.0 Kb) TX bytes:234547 (229.0 Kb)eth1 Link encap:Ethernet HWaddr 90:E2:BA:06:CF:7F UP BROADCAST SLAVE MULTICAST MTU:1500 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:0 errors:0 dropped:0
27、overruns:0 carrier:0collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)eth2 Link encap:Ethernet HWaddr 90:E2:BA:06:CF:7C UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1RX packets:1 errors:0 dropped:0 overruns:0 frame:0TX packets:164 errors:0 dropped:0 overruns:0 carrier:0collis
28、ions:0 txqueuelen:1000 RX bytes:249 (249.0 b) TX bytes:10008 (9.7 Kb)eth3 Link encap:Ethernet HWaddr 90:E2:BA:06:CF:7D UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1RX packets:1 errors:0 dropped:0 overruns:0 frame:0TX packets:163 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen
29、:1000 RX bytes:249 (249.0 b) TX bytes:9906 (9.6 Kb)eth4 Link encap:Ethernet HWaddr 90:E2:BA:06:CF:7E UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1RX packets:1 errors:0 dropped:0 overruns:0 frame:0TX packets:162 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000 RX bytes:249
30、 (249.0 b) TX bytes:9828 (9.5 Kb)eth5 Link encap:Ethernet HWaddr 00:1E:67:2E:B3:E5 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1RX packets:8 errors:0 dropped:0 overruns:0 frame:0TX packets:168 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000 RX bytes:1413 (1.3 Kb) TX byte
31、s:10188 (9.9 Kb)lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0inet6 addr: :1/128 Scope:HostUP LOOPBACK RUNNING MTU:16436 Metric:1RX packets:76067 errors:0 dropped:0 overruns:0 frame:0TX packets:76067 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:0 RX bytes:11862127 (11.3 Mb) TX bytes:11862127 (11.3 Mb)/home/maintenance #2、路由信息查看nb-appliance:/etc/sysconfig/network # more routesdefault 10.9.6.254 - -3、检查 Appliance 版本及 NetBackup 版本szbaksrv.Software List versionAppliance Version: 2.5NetBackup Version: 7.5.0.2Build Date: 20120510szbaksrv.Software
