1、 仿真图形运行后结果#ifndef _TOU_H_#define _TOU_H_#include#include /#include /Keil library #define uchar unsigned charenum TEMP,HUMI;sbit DATA = P11;sbit SCK = P10;sbit RS = P20;sbit RW = P21;sbit E = P22;sfr DBPort = 0x80; /P0=0x80,P1=0x90,P2=0xA0,P3=0xB0.数据端口/* DS1602 函数声明 */void LCD_Initial();void GotoXY(u
2、nsigned char x, unsigned char y);void Print(unsigned char *str);void LCD_Write(bit style, unsigned char input);/* SHT10 函数声明 */void s_connectionreset(void);char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode);void calc_sth10(float *p_humidity ,float *p_temperature);/
3、float calc_dewpoint(float h,float t);#endif/*/SHT10 程序（ SHT10.c）：/#include#define noACK 0 /继续传输数据，用于判断是否结束通讯#define ACK 1 /结束数据传输；/地址 命令 读/写#define STATUS_REG_W 0x06 /000 0011 0#define STATUS_REG_R 0x07 /000 0011 1#define MEASURE_TEMP 0x03 /000 0001 1#define MEASURE_HUMI 0x05 /000 0010 1#define RESE
4、T 0x1e /000 1111 0/写字节程序char s_write_byte(unsigned char value) unsigned char i,error=0; for (i=0x80;i0;i=1) /高位为 1，循环右移 if (i /和要发送的数相与，结果为发送的位else DATA=0; SCK=1; _nop_();_nop_();_nop_(); /延时 3us SCK=0;DATA=1; /释放数据线SCK=1; error=DATA; /检查应答信号，确认通讯正常_nop_();_nop_();_nop_();SCK=0; DATA=1;return error;
5、 /error=1 通讯错误/读字节程序char s_read_byte(unsigned char ack)/- unsigned char i,val=0;DATA=1; /释放数据线for(i=0x80;i0;i=1) /高位为 1，循环右移 SCK=1; if(DATA) val=(val|i); /读一位数据线的值 SCK=0; DATA=!ack; /如果是校验，读取完后结束通讯；SCK=1; _nop_();_nop_();_nop_(); /延时 3us SCK=0; _nop_();_nop_();_nop_(); DATA=1; /释放数据线return val;/启动传输
6、void s_transstart(void)/ generates a transmission start / _ _/ DATA: |_|/ _ _/ SCK : _| |_| |_ DATA=1; SCK=0; /准备_nop_();SCK=1;_nop_();DATA=0;_nop_();SCK=0; _nop_();_nop_();_nop_();SCK=1;_nop_();DATA=1; _nop_();SCK=0; /连接复位void s_connectionreset(void)/ communication reset: DATA-line=1 and at least 9
7、 SCK cycles followed by transstart/ _ _/ DATA: |_|/ _ _ _ _ _ _ _ _ _ _ _/ SCK : _| |_| |_| |_| |_| |_| |_| |_| |_| |_| |_| |_ unsigned char i; DATA=1; SCK=0; /准备for(i=0;i=1 in case of no response form the sensor */温湿度测量char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char
8、mode)/ 进行温度或者湿度转换，由参数 mode 决定转换内容； / enum TEMP,HUMI; /已经在头文件中定义unsigned error=0;unsigned int i;s_transstart(); /启动传输switch(mode) /选择发送命令case TEMP : error+=s_write_byte(MEASURE_TEMP); break; /测量温度case HUMI : error+=s_write_byte(MEASURE_HUMI); break; /测量湿度default : break; for (i=0;i100)rh_true=100; /湿
9、度最大修正if(rh_true/内部等待函数*unsigned char LCD_Wait(void)RS=0;RW=1; _nop_();E=1; _nop_(); E=0;return DBPort; /向 LCD 写入命令或数据*#define LCD_COMMAND 0 / Command#define LCD_DATA 1 / Data#define LCD_CLEAR_SCREEN 0x01 / 清屏#define LCD_HOMING 0x02 / 光标返回原点void LCD_Write(bit style, unsigned char input)E=0;RS=style;R
10、W=0; _nop_();DBPort=input; _nop_();/注意顺序E=1; _nop_();/注意顺序E=0; _nop_();LCD_Wait(); /设置显示模式*#define LCD_SHOW 0x04 /显示开#define LCD_HIDE 0x00 /显示关 #define LCD_CURSOR 0x02 /显示光标#define LCD_NO_CURSOR 0x00 /无光标 #define LCD_FLASH 0x01 /光标闪动#define LCD_NO_FLASH 0x00 /光标不闪动void LCD_SetDisplay(unsigned char D
11、isplayMode)LCD_Write(LCD_COMMAND, 0x08|DisplayMode); /设置输入模式*#define LCD_AC_UP 0x02#define LCD_AC_DOWN 0x00 / default#define LCD_MOVE 0x01 / 画面可平移#define LCD_NO_MOVE 0x00 /defaultvoid LCD_SetInput(unsigned char InputMode)LCD_Write(LCD_COMMAND, 0x04|InputMode);/初始化 LCD*void LCD_Initial()E=0;LCD_Write
12、(LCD_COMMAND,0x38); /8 位数据端口,2 行显示,5*7 点阵LCD_Write(LCD_COMMAND,0x38);LCD_SetDisplay(LCD_SHOW|LCD_NO_CURSOR); /开启显示, 无光标LCD_Write(LCD_COMMAND,LCD_CLEAR_SCREEN); /清屏LCD_SetInput(LCD_AC_UP|LCD_NO_MOVE); /AC 递增, 画面不动/液晶字符输入的位置*void GotoXY(unsigned char x, unsigned char y)if(y=0)LCD_Write(LCD_COMMAND,0x8
13、0|x);if(y=1)LCD_Write(LCD_COMMAND,0x80|(x-0x40);/将字符输出到液晶显示void Print(unsigned char *str)while(*str!=0)LCD_Write(LCD_DATA,*str);str+;/*/主函数（main.c）：/#includetypedef union /定义共用同类型 unsigned int i;float f; value;/延时函数void delay(int z) /z 为毫秒数int x,y;for(x=z;x0;x-)for(y=125;y0;y-);void main() unsigned
14、int temp,humi;value humi_val,temp_val; /定义两个共同体，一个用于湿度，一个用于温度/ float dew_point; /用于记录露点值unsigned char error; /用于检验是否出现错误unsigned char checksum; /CRC uchar wendu6; /用于记录温度uchar shidu6; /用于记录湿度LCD_Initial(); /初始化液晶 GotoXY(0,0); /选择温度显示位置Print(“TEMP: %C“); /5 格空格GotoXY(0,1); /选择湿度显示位置Print(“HUMI: %RH“)
15、; /5 格空格s_connectionreset(); /启动连接复位while(1)error=0; /初始化 error=0，即没有错误error+=s_measure(unsigned char*) /温度测量error+=s_measure(unsigned char*) /湿度测量if(error!=0) s_connectionreset(); /如果发生错误，系统复位else humi_val.f=(float)humi_val.i; /转换为浮点数temp_val.f=(float)temp_val.i; /转换为浮点数calc_sth10( /修正相对湿度及温度/ dew_
16、point=calc_dewpoint(humi_val.f,temp_val.f); /计算 e dew_pointtemp=temp_val.f*10;humi=humi_val.f*10;GotoXY(5,0); /设置温度显示位置wendu0=temp/1000+0; /温度百位 wendu1=temp%1000/100+0; /温度十位wendu2=temp%100/10+0; /温度个位wendu3=0x2E; /小数点wendu4=temp%10+0; /温度小数点后第一位Print(wendu); /输出温度 GotoXY(5,1); /设置湿度显示位置 shidu0=humi/1000+0; /湿度百位shidu1=humi%1000/100+0; /湿度十位shidu2=humi%100/10+0; /湿度个位shidu3=0x2E; /小数点shidu4=humi%10+0; /湿度小数点后第一位Print(shidu); /输出湿度 delay(800); /等待足够长的时间，以现行下一次转换
