1、光分路器连接器技术规范H.2.10 The Cassette Splitter type shall be equipped with minimum of one (1) meter ruggedized pigtail with and without SC/UPC connector. 盒式分路器应带至少1米耐用的尾纤（带或不带SC/UPC 连接器）H.2.11 The input of Micro-splitter type shall be equipped with minimum of one (1) meter tight buffered tube with and with
2、out SC/UPC connector. 微型分路器的输出端应配1米紧的松套管， 带或不带SC/UPC连接器。H.2.12 The output of Micro-splitter type shall be single fibres. 。微型分路器的输出端应是单纤。H.2.13 The dimension of the Micro-splitter type shall be able to fit into the splice/splitter holder on the splice tray. 微分路器的尺寸应能放进集纤盘上相应的分路器卡槽内。H.2.14 Maximum dim
3、ension of the Cassette Splitter type shall be 130mm (W) x 160mm (H) x 30mm (D). 盒式光分路器的最大尺寸 为130mm (宽) x 160mm (高) x 30mm (深)H.2.15 Maximum dimension of the Rack Mountable Splitter type shall be 2 Rack Unit (2U) and shall be able to fit into standard 19 inches ETSI rack system of Optical Distributio
4、n Frame. The dimension of Optical Distribution Frame as follow: 机架式光分路器应为2个机架单元，能适配在19 英寸配线架 ETSI机架上。配线架尺寸如下：配线架尺寸高(H) 宽 (W) 深度 (D) 2200mm 600mm 300mm H.2.16 Each fibre output shall be provided with a numbering label for circuit identification purpose. It shall be labelled on durable material in suc
5、h a manner as to be permanently legible and properly displayed. 光纤输出部部应有识别标志。标志经久不变。 H.2.17 The Tenderer shall submit proposed technical drawings complete with dimensions for the various sizes of Optical Splitter Module. 投标方应提供各种光分路器的全套技术图纸。H.3 CONSTRUCTION AND MATERIALS 结构和材料H.3.1 Single Mode Fibre
6、 Cable 单模光缆H.3.2 The optical fibre shall conform to the requirement of ITU-T Recommendation G.657A.光纤应符合ITU-T要求及 G.657A要求.H.3.3 The optical specifications are shown below:- 技术要求如下 :Parameter参数 Specification 参数a. Operating Wavelength 操作波长 1260 1650nm b. Polarization Dependent Loss (PDL)偏振损耗 0.2 dB c.
7、 Directivity方向性 55 dB d. Return Loss 回波损耗 55 dB H.3.4 The operating wavelength shall comply with ITU-T G.983.1 recommendation. The Optical Splitter shall operate in the following wavelength:-操作波长应符合ITU-T G.983.1要求。应在下列波长下操作：a. 1310nm data/ voice upstream signal b. 1490nm data/ voice downstream signa
8、l c. 1550nm RF video signala. 1310nm 数据/语音上行信号b. 1490nm 数据/语音下行信号下c. 1550nm 射频视频信号d. 1650nm 监控作用和未来的网络 H.3.5 The insertion loss (IL) and uniformity for the single input Optical Splitter and various splitting ratio shall meet the following requirements: 1分光分路器的插入损耗（IL）和一致性应符合下列要求：分光率 Insertion Loss插入
9、损耗(dB) Uniformity一致性 (dB) 1 x 2 3.6 0.4 1 x 4 7.3 0.5 1 x 8 10.5 0.8 1 x 16 13.8 1.0 1 x 32 17.1 1.3 1 x 64 20.5 2.0 H.3.6 The insertion loss (IL) and uniformity for the dual input Optical Splitter with various splitting ratio shall meet the following requirements: 2分光分路器的插入损耗（IL ）和一致性应符合下列要求：Splitt
10、ing ratio分光率Insertion Loss插入损耗(dB) Uniformity一致性 (dB) 2 x 2 4.2 0.6 2 x 4 7.5 1.2 2 x 8 10.8 1.8 2 x 16 14.1 2.4 2 x 32 17.4 3.0 2 x 64 20.7 3.6 H.3.7 应提供各种光分路器的操作安装手册。 An Operation and installation manual shall be provided with each Optical Splitter Module. H.4 FACTORY TEST REPORT 厂检报告H.4.1 The fac
11、tory test method and requirements of the offered splitter shall comply with Telcordia GR-1209 and GR-1221 standard. The Tenderer shall provide a detailed qualification test report in tender documentation as evidence to guarantee the reliability of the offered splitter type. 工厂检测方法和要求应符合GR-1209 和 GR-
12、1221标准。 投标人应提供详细的资质试验报告，作为光分路器具有可靠性的证明。H.4.2 The mechanical, physical and environmental test are summarize in the format as per table A below. 下表是机械试验、物理试验和环境试验的汇总：TABLE A 表ATest 试验 Test Conditions 检测条件Pass/Fail Criteria通过/ 未通过标准a. Damp heat 湿热测试85 C 85 % 相对湿度 IL 0.5 dB 500 hrs b. Temperature Cyclin
13、g 温度循环 -40C 到 85C IL 0.5 dB 100 个循环Environmental Tests环境试验c. High Temperature Dry Storage 高温干燥存贮 85 C IL 0.5 dB 2000 hrs Mechanical Tests机械试验 d. Mechanical Shock 机械摇动 500 G 5 次/每个方向 6 个方向 1 豪秒 IL 0.5 dB e. Variable Frequency Vibration 振动频率最大加速度：20G20 20000 Hz 每个循环4分钟 4次循环/轴向 IL 0.5 dB Fiber Integrit
14、y Tests 光完整性试验f. Cable Retention 光缆保持力900 um 光纤：0.34 kgf 带状光纤：0.23 *n kgf IL 0.5 dB g. Side Pull 侧拉900 um光纤： 0.23 kgf IL 0.5 dB H.5 SAMPLE 样品H.5.1 The Tenderer is required to submit a sample of each type and/or model of the Optical Splitter Module offered when requested for evaluation purposes. 投标人要
15、求提供各种类型的光分路器1个作为评估样品。H.5.2 The sample will provide TM an avenue to verify and validate the specifications claimed in the tender bid. 样品作为电信验证投标资料的依据。H.5.3 The sample shall be approved by SIRIM or any equivalent authorized body. A copy of type-approved letter or certification shall be submitted during tender submission. 样品应通过SIRIM或同等检测机构的型式认证。H.6 包装和标志：应先用聚乙烯片包裹，然后再装在标准纸箱内，纸箱上有电信标志。外包装上应有以下标志：1. TMs Material Code Number : 2. Description of item : 3. Contract Number : 4. Suppliers/ Manufacturers Name : END OF CHAPTER H
