ImageVerifierCode 换一换
格式:PPT , 页数:9 ,大小:987KB ,
资源ID:12067054      下载积分:10 金币
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝    微信支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.docduoduo.com/d-12067054.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录   QQ登录   微博登录 

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(排气系统设计24288.ppt)为本站会员(gnk289057)主动上传,道客多多仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知道客多多(发送邮件至docduoduo@163.com或直接QQ联系客服),我们立即给予删除!

排气系统设计24288.ppt

1、為何排氣仍然還是一個問題? Why venting is still a problem ? 因為降低射速,讓積風有較多的時間逃氣,是一件太容易的事。但是 Because it is too easy to slow down the injection speed and give the trapped air more time to escape. But .,排氣 Vent,射速一降,熔膠溫度很快降低,射壓必須提高,殘餘應力隨之提高,翹曲的可能性增加。 如果想藉提高料溫,以降低射壓,料溫必須升得很高,這樣又會引起塑料裂解。 When injection speed is lower,

2、 melt temperature goes down very fast, injection pressure has to be increased, residual stress is increased and the possibility getting warppage becomes higher. If one would like to increase barrel temperature to reduce the required injection pressure, the barrel temperature has to be increased to a

3、 quite high level and polymer degradation would be induced.,排氣 Vent,高料溫和高射壓都說明充填系統有了流動的問題,Both high barrel temperature and high injection pressure are indications of flow problem in the filling system.,排氣 Vent,我們常發現: 射速提高時,塑料表現得更為出色。 It is quite common that material performs better when it is inject

4、ed faster. 最適化螺桿速度充分運用摩擦熱,將塑流保持在最佳狀態。許多充填和翹曲的問題也就迎刃而解。 An optimized ram speed profile fully uses the friction heat to keep the best flow characteristics, which corrects many of the fill and warpage problems.,排氣 Vent,有了適當的排氣,射速可以提高,充填和保壓可達良好狀態,不須過度增加料管和噴嘴的溫度。,With proper venting, the injection speed

5、could be increased to achieve good fill and pack conditions, without having to raise the barrel and nozzle heats, improperly.,排氣 Vent,深度(depth) : 1. 0.075 mm易流塑料(easy-flow mat.) 2. 0.125 mm難流塑料(stiffer-flow mat.) 3. 深度深到流道末端見毛邊為準 (deep enough to feel flash at runner end) 寬度(width) : 和流道同寬(as wide as

6、 runner dia.) 排氣唇部(vent lip): 1.5mm A1拋光(finish) 排氣通道通大氣(vent channel to atmosphere): 1mm深(deep),流道排氣 Runner Vents,深度(depth) : 參照廠商建議 (refer to manufacturers recommendation) 寬度(width) : 全圓周長(whole perimeter) or 5mm 長度(length) : 1.5mm A1拋光(finish) 排氣通道通大氣(vent channel to atmosphere): 1mm深(deep),分模面排氣 Parting Line Vents,分模面排氣 Parting Line Vents,深度(depth) : 參照廠商建議 (refer to manufacturers recommendation) 寬度(width) : 全圓周長 (whole perimeter) 長度(length) : 1.5mm 排氣溝(vent groove): 1mm深 (deep),頂出銷或心型銷排氣 Ejector and Core Pin Vents,

本站链接:文库   一言   我酷   合作


客服QQ:2549714901微博号:道客多多官方知乎号:道客多多

经营许可证编号: 粤ICP备2021046453号世界地图

道客多多©版权所有2020-2025营业执照举报